How are the Derale Adapter Fittings # D13018 Installed and Used to Install a Transmission Cooler
Question:
I have a 07 Silverado with a 4.3L V6. I believe I need these fittings but do not understand why there are two. I see one is a male and one a female. I assume the male adapter threads into the radiator where the supply hot fluid enters after I remove the existing line? I then attach a rubber trans hose and feed to inlet on cooler? Not sure where the other included adapter goes. Do you have a video showing where these are used? THanks
asked by: Derek
Expert Reply:
The male end of the Derale Radiator Adapter part # D13018 that you referenced does thread into the outlet side of the factory cooler in your radiator. The female side of this adapter would thread onto the male side of the coolant line that you removed from the factory cooler.
I realize that's probably hard to visualize so I attached a diagram that shows how both sides of the adapter are used.
I also attached an FAQ article on transmission coolers, plus a video of one being installed. The exact same adapter isn't being used in the video, but it gives you a rough idea on how a cooler would install.
Product Page this Question was Asked From
Derale Radiator Adapter Fittings for GM
- Accessories and Parts
- Transmission Coolers
- Radiator Adapters
- Derale
more information >
Continue Researching
- Shop: Derale Radiator Adapter Fittings for GM
- Shop: Transmission Cooler
- Video: Derale Snap In Radiator Adapter Fitting Installation
- Shop: Derale Snap-In Radiator Adapter Fitting for GM
- Video: Transmission Cooler Installation - 2011 Chevrolet Suburban
- Q&A: How Does Derale Radiator Fitting for Transmission Coolers Install on a 2002 Chevy S10 2.2 Liter
- Video: Derale Transmission Cooler Installation - 2009 GMC Yukon
- Video: Review of Derale Transmission Cooler Adapter Fittings for GM - D13018
- Search Results: transmission cooler mounting kit
- Shop: Derale Single-Hose Transmission Cooler Installation Kit w/ 11/32" Inner Diameter Hose
- Shop: Derale Series 9000 Plate-Fin Transmission Cooler Kit w/ NPT Inlets - Class V - Extra Efficient
- Shop: Derale Remote Mounting Kit for Transmission Coolers - 1/2" Lines
- Shop: Replacement Shoe and Lining Kit for 12" Manual-Adjust Brake Assembly - 5,200 lbs to 7,000 lbs
- Q&A: How Many Derale Radiator Adapter Fittings Are Needed To Install Transmission Cooler 1999 GMC Yukon
- Q&A: Towing Capacity of a 2003 Chevrolet Suburban 5.3L Engine with 3.73 Gears
- Q&A: Which is Transmission Fluid Return Line on Radiator of 2000 Chevy Silverado
- Q&A: How Many Derale Snap-In Radiator Adapter Fitting for GM, # D13035 are Needed on a 2010 GMC Canyon
- Q&A: Attaching Hose to Transmission Lines When Installing Transmission Cooler on 2005 Chevy Suburban
- Q&A: Fitting Needed to Install Transmission Cooler on 2003 Chevy Silverado Without Cutting Lines
- Shop: Brake Controller
- Shop: Trailer Wiring
- Shop: Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class IV - Efficient
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Brake Controller
- Search Results: 44649
- Video: Tow Ready 4-Pole Mounting Bracket Installation