Trailer Fender Close to 29-1/2" Long, 13" Tall & 9-1/2" Wide

Question

Question:

I need replacement fenders for a Ranger boat trailer. The measurements are 9.5 wide, 29.5 long, 13 high. Do you have anything close to this avail?

asked by: Scott

0

Expert Reply:

We do have a couple options for trailer fenders that are close to 29-1/2" long, 13" tall and 9-1/2" wide, and I'll go ahead and list them out, as well as their dimensions:

- 31.3" long x 9.7" wide x 12.75" tall: Fulton Single Axle Trailer Fender # F008564

- 30" long x 9" wide x 13-1/4" tall: Single Axle Trailer Fender for Boat Trailers # HP38VR

expert reply by: Kyle S

0

Answer 1

The closest fender we have to what you are looking for is the Single Axle Fender part #HP79VR which is 28 inches long, 7-3/4 inches wide, and 10 inches tall. This has a backing plate too.

view full answer...

Answer 2

For 13 inch trailer wheels we have the Single Axle Trailer Fender with Backing part #HP79VR which would be a great option. Here are the dimensions for you to compare to your trailer. 7-3/4" Wide x 28" long x 10" tall.

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 10

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Trailer Fender Close to 29-1/2" Long, 13" Tall & 9-1/2" Wide

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching