Pre-Greased Trailer Hub for Floe Pro 100 Snowmobile Trailer

Question

Question:

Hi I have a floe pro 100 2 place snowmobile trailer. Looking for prepacked hub assembly. 5- 4 1/2 bolt pattern.

asked by: Jared

0

Expert Reply:

From previous customers who have the same Floe Pro 100 trailer we have determined that the correct replacement hub would be for a 2k axle like with the part # AKIHUB-545-2-1K which is pre-greased.

expert reply by: Jameson C

0

Answer 1

Luckily, FLOE International is still around. I was able to find that your 10 foot tilt single axle snowmobile trailer used an L44649 inner and outer wheel bearing. Your snowmobile trailer was equipped from the factory with idler hubs that had a 5 on…

view full answer...

Answer 2

I may have another option for you, but the Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 72" Long - 2,200 lbs #T20BTR-EZ-7258 you were looking at uses inner and outer bearing #L44649 which is used for 2000lb hubs like the Dexter Trailer…

view full answer...

Answer 3

Yes, the Dexter Trailer Idler Hub Assembly part #8-91-05UC1 will work with the bearing part #L44643 and the race part #L44610. They both have a 1.980" outer diameter which is why they are compatible with the above trailer hub. As long as your…

view full answer...

Answer 4

I have a solution for you. However, you are going to need a little more information to make sure you receive the correct hubs to replace you current oil bath hubs. You will need the bearing numbers of your current hub to match with the replacement…

view full answer...

Answer 5

Are you sure the diameter of the spindle is 1.25 inches where both bearings ride? That's not typical for a 2,000 lb axle but if instead the diameter is 1.06 inch then you could use the hub part #AKIHUB-545-2-2K which has the 5 on 4-1/2 bolt…

view full answer...

Answer 6

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 7

A 2000 lb axle uses a straight spindle, with both the inner and outer bearing being the same size. The hubs needed will depend on the number of lugs your current hubs have and which inner/outer wheel bearings are used. I'll give you a run-down on…

view full answer...

Answer 8

We can certainly point you in the right direction. Unfortunately we do not have literature that will give us spindle/bearing sizes based off a year, make and model of trailer. So it may be difficult to recommend a direct replacement without a bit…

view full answer...

Answer 9

Henschen has been out of business for about 12 years, so I wasn't able to find much information about your axles online. From what I saw in the forums, they used a standard spindle for a 3.5K axle, so it should use a L44649 outer and a L68149…

view full answer...

Answer 10

What you listed is compatible with a BT8 2,000 lb axle. That means that the part #34822545BX would be what you need.

view full answer...

Answer 11

From all the photos I saw online, it looks like Floe used grommet mounted 2-1/2 inch marker lights and standard 6-1/2 by 2-1/2 inch oblong taillights. If that's the case, for the amber 2-1/2 inch I would recommend #MCL59AB and #MCL59RB for the…

view full answer...

Answer 12

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Pre-Greased Trailer Hub for Floe Pro 100 Snowmobile Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching