Availability Of 5 On 4-1/2 Hubs That Go On A Straight Spindle
Question:
Im having difficulty finding a pre-greased hub replacement or any hub really for use on a straight spindle. Measured the spindle with calipers based on the image attached. A and B are both 1.25 C and D are both 1.05 E is 0.8 5 on 4-1/2 has bearing buddies that are measuring 2.12inch OD I have checked measurements with different tools, cant seem to find anything that corresponds to these measurements. Thanks
asked by: Jason S
Expert Reply:
Your picture did not come thru, but we do offer a few hubs for a straight spindle. For example the hub # AKIHUB-545-2-G-EZ-2K uses a # L44649 (1.063" inner diameter) for both the inner and outer bearing. It also has the 5 on 4-1/2" bolt pattern. This hub would use a 1.99" bearing buddy like the # BB1980A.
We also have hubs like the # AKIHUB-545-2-G-EZ-1K which use a # L44643 (1" inner diameter) inner and outer bearing. These are the only hubs we carry for a straight spindle.
Products Referenced in This Question
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- Easy Grease
- EZ Lube
- L44643
- L44643
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Trailer Hubs and Drums
- Hub
- Easy Grease
- EZ Lube
- L44649
- L44649
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- etrailer
more information >
Bearing Buddy Bearing Protectors - Model 1980A w/ Auto Check - Chrome Plated (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.98 Inch
- Bearing Buddy
more information >
Replacement Trailer Hub Bearing - L44643
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.000 Inch I.D.
- Bearing L44643
- Race L44610
- 2000 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Product Page this Question was Asked From
Square #84 Spindle for 3,500-lb Trailer Axles - 1-1/2" Wide
- Trailer Spindles
- Standard Spindle
- 1-1/2 Inch Diameter
- Square
- For 3500 lb Axle
- TruRyde
more information >
Continue Researching
- Q&A: Recommended Replacement Grease Seal for 2014 Shorelander Boat Trailer
- Q&A: Trailer Grease Seal to Replace 127194TB
- Article: How to Charge a Dump Trailer Battery
- Q&A: Will the Correct Track Trailer Alignment and Lift Kit Prevent Nose High Towing
- Q&A: Does Correct Track Trailer Alignment Kit # RR23QX Come with Enough Brackets for Tandem Trailer
- Q&A: How Does the Correct Track Trailer Alignment and Lift Kit Really Work
- Q&A: Replacing Parallex 7345 Converter to One that is Compatible with Lithium Batteries
- Q&A: Recommended Replacement For A WFCO WF-8750P Power Center
- Article: How to Measure for Travel Trailer and Fifth Wheel Steps
- Article: Trailer Hitch Receiver Sizes
- Article: Roadmaster Vehicle Specific Base Plates
- Article: Trailer Maintenance Schedule
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Most Popular Wheel Bearings