Procedure To Perform Hard Reset On Furrion Television

Question

Question:

After holding down the power button for one minute do you continue to hold down the power button and plug the tv back in? Or, after the one minute, do you release release the power button, plug in the tv and then press power again?

asked by: Mark

0

Expert Reply:

To perform a hard reset on your Furrion television you will first unplug the TV. Then you will hold the power button down for one minute. Release the power button and then plug back in the TV. After you plug in the TV you will press the power button once to start the setup process.

expert reply by: Bud M

0

Answer 1

I reached out to my contact at Furrion who said that if your Furrion Remote, like part #FR34FR, isn't working even after replacing the batteries then there are 2 other things you can try. First off inspect the contacts where your batteries…

view full answer...

Answer 2

Other than replacing the T.V there is not much else that can be done, however before you go and replace the unit, I recommend trying one more thing. What you're going to want to do is unplug the T.V from power for approximately 60 seconds,…

view full answer...

Answer 3

For your Jensen LED 110V RV TV #JE2417 I have a few solutions to potentially fix your issue. Start by checking your coax or splitter connections, typically located behind a plate near your T.V. Usually, all that needs to be done to resolve this, is…

view full answer...

Answer 4

There are a number of reasons why your Furrion Unismart Universal Remote Control #FR34FR may be having issues after you changed the batteries. If you take a look at the cut out of the linked installation instructions I added you can see the potential…

view full answer...

Answer 5

The Furrion #FR34FR remote should be ready to use on the TV and Stereo. The fireplace will need to be programmed based on the specific fireplace instructions. To switch to fireplace on the remote you hit TV again. I've attached some photos to…

view full answer...

Answer 6

If you've ensured that your battery contacts are good and not obstructed or dirty, and the batteries don't need to be changed, then I recommend replacing the entire remote with the Furrion Unismart Remote Control #FR34FR.

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Procedure To Perform Hard Reset On Furrion Television

Product Page this Question was Asked From

Continue Researching