What Is The Torque Spec For The 4 Bolts On 10" Backing Plates

Question

Question:

What is the correct torque spec assigned to the four studs for installing a new Dexter Brake Shoe Assembly to the axle flange housing? Referencing Dexter Part # 023-026-00 Left Hand Assembly, and #023-027-00 Right Hand Assembly respectively. This is a standard installation for a 3,500 lb. axle and a 10inch x 2 1/4inch sized brake shoe assembly. Dexter is very vague as to what this correct torque spec is, and I carefully read through their entire light duty manual for components within this size class.

asked by: Matthew

0

Expert Reply:

There is not a "set in stone" torque spec for the brake flange bolts on the 10" backing plates like the Dexter # 23-26 and # 23-27. When we install these here at our shop in Missouri, we will go for 45-50 ft lbs.

expert reply by: Jesse M

0

Answer 1

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding…

view full answer...

Answer 2

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn…

view full answer...

Answer 3

Shackle links can flip when the trailer is unloaded since there isn't enough weight to keep them in proper position, and while a new, shorter equalizer may help, the easiest thing to check is the shackle links. Shackles that are too short…

view full answer...

Answer 4

The Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 3.5K #23-468-469 are not designed to be manually adjusted in the way you are describing. There isn't really a way to back off the adjustment because…

view full answer...

Answer 5

Yes, the Nev-R-Adjust Electric Brake Assemblies come assembled and ready to install, The assemblies will adjust themselves as you drive after the initial installation. For install details and some product demonstration videos, click the provided…

view full answer...

Answer 6

There are a couple of things that caught my eye in your question. First, you mentioned taking the trailer to have the bearings packed. It is possible that in the process, they may have got some grease on the shoes or another component of the brakes…

view full answer...

Answer 7

If you can pull the hub off that is going to be the easiest way to adjust the brakes looser but if it's super tight that might be hard. Otherwise you would have to use a drum brake spoon like the part #W80630 to try and move the adjuster back to…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

Base plate kits are somewhat time consuming but they aren't too terribly long. I once asked our install guy that's been here forever how long to set aside for a base plate kit install and he said a "long afternoon" and you'd be…

view full answer...

Answer 10

Unfortunately we do not have a way to replace the keys without knowing the key number for the lock. If they happened to have written down the key number from the lock then we will be able to get you a replacement. The etrailer Trailer Hitch Receiver…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

What Is The Torque Spec For The 4 Bolts On 10" Backing Plates

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching