Rubber Hitch Cover Recommendation for a etrailer Trailer Hitch Receiver

Question

Question:

Need a rubber hitch cover.

asked by: Jeffrey F

0

Expert Reply:

For a rubber hitch cover that'll work with your etrailer Trailer Hitch Receiver # e28AR you can use the etrailer Rubber Hitch Cover for 2" Trailer Hitches # 22282.

expert reply by: Bryce D

0

Answer 1

Looking at the installation instructions, as well as the video, trimming will not be required for the installation of the #e28AR. It appears as though the removal of panels only applies to the Kia Sorento, not your 2023 Santa Fe. However, you will…

view full answer...

Answer 2

When it comes to installing a trailer hitch onto your 2023 Kia Sorento I recommend the etrailer brand #e28AR Class III hitch because the installation of the hitch is very easy, pretty much have to just raise it into place and insert the bolts. Once…

view full answer...

Answer 3

The bolts that come with the Curt Trailer Hitch Receiver #C34ER are size M12 X 1.25 X 40mm.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Rubber Hitch Cover Recommendation for a etrailer Trailer Hitch Receiver

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching