Which Hub Do I Need for the TRU57FR Spindle

Question

Question:

this is the spindle i want, i dont know which hub to order, i want the 6 on 5-1/2 patern. 213-5uc1 sounds right but dosnt tell me the bearing size.... can you help?

asked by: JIm

0

Expert Reply:

The hub you will need for the #42 Spindle, item # TRU57FR, is the Trailer Hub Assembly - 5,200 & 6,000 lbs Axles - 6 on 5-1/2, item # 42655UC1.

expert reply by: Robert G

0

Answer 1

In order to pick out the correct bearing buddy you will need know the pilot hole of your hub. To do this, remove the wheel and tire and remove the grease cap from the center of the hub. Usually it is a metal cap that is just lightly hammered into…

view full answer...

Answer 2

Even though you do not have EZ lube axles you will be able to add EZ lube hubs and drums, however, you will not have the EZ lube feature on his axles by installing the EZ lube hub and drums. For you to be able to easily pack grease into your hubs and…

view full answer...

Answer 3

You can use Bearing Buddies such as #BB1980A-SS on your trailer with brakes you just need to make sure you don't overfill them because if grease gets on brake pads the pads will need to be replaced. So as long as you are sure you aren't using…

view full answer...

Answer 4

I can tell you how to determine the correct spindle based on your measurements, and what you will need is a digital caliper, though the first thing you need to know is the weight rating of your trailer axle. From there, what you need to do is measure…

view full answer...

Answer 5

We have the #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter #TRU37FR and the #42 Spindle for 5,200-lb to 7,000-lb Trailer Axles - 2-1/4" Diameter #TRU57FR which are both compatible with 7,000 lb axles. Both…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Which Hub Do I Need for the TRU57FR Spindle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching