What is the Rise on Curt Euro-Style Ball Mount # 45562

Question

Question:

what is the height from top of hitch to under ball straight up how many in .

asked by: Larry M

0

Expert Reply:

For Curt Euro style ball mount # C45562, it measure 3-1/8 inches from the top of the shank to the beginning of the vertical curve that leads up to the ball. To the bottom of the ball is just over another 2 inches so it is about 5-3/8 inches to the bottom of the ball measuring from the top of the shank. I have included a picture showing the measurements.

expert reply by: Michael H

0

click to enlarge

Answer 1

Usually air bags are used to help level out a load or offer extra support to the OEM suspension system, but it isn't unheard of to use them for smoothing out the ride from the OEM suspension while it's unloaded. I reached out to my contact at…

view full answer...

Answer 2

The only difference between the TST TPMS #TST-507-RV-6-C and #TST-507-FT-6-C is the type of tire sensors that are included with each kit. Kit #TST-507-RV-6-C comes with 6 standard tire sensors, whereas kit #TST-507-FT-6-C comes with 6 flow through…

view full answer...

Answer 3

The recommended 2 inch Euro style ball mount for Curt trailer hitch #C11352 on a 2015 Nissan Altima is #C45572. I went out to the warehouse and pulled one to take some measurements. From the center of the pin hole to the part of the shank where it…

view full answer...

Answer 4

There isn't a specific distance you want to have between the bumper of a vehicle and the hitch ball, but in general you'll want more than an inch. This will give you additional leeway when hitching up the trailer so that you don't slam…

view full answer...

Answer 5

The part #C45562 you mentioned is the Curt Euro Style ball mount with 5-1/8 inches of rise. I just went out to our warehouse and measured it for verification.

view full answer...

Answer 6

To determine the amount of rise or drop in a ball mount that you will need to tow a trailer level there are a couple of measurements needed. First make sure the trailer is on level ground. Use the jack to make the trailer level then measure from the…

view full answer...

Answer 7

Thanks for reaching out, John! The Curt Class II Euro Style Drawbar #C45552 has a 2" hitch ball. The hitch ball is fixed and can't be removed so if you want this style and you need to be able to use both a 1-7/8" and 2" hitch ball…

view full answer...

Answer 8

To measure for safety chains you will want to have the trailer hooked up to your tow vehicle with it just about jack knifed as this is the furthest the safety chains will be stretched. You will measure from one side of the tongue where you will be…

view full answer...

Answer 9

For your 2021 Mazda 3 Hatchback, I recommend going with the Curt #C98BR. At the time of this writing, this is actually the only hitch we have that is confirmed for your vehicle, but due to its hidden design, it is one that I do like. With this being…

view full answer...

Answer 10

Thank you for all of the info and the pictures! I believe from everything you are saying that you are trying to use the Roadmaster Falcon All Terrain Tow Bar #RM-522 and the Swagman G10 S64682 with your Roadmaster Dual Hitch Receiver Adapter…

view full answer...

Answer 11

The correct trailer for a 2019 Mazda 3 Hatchback is the Draw-Tite Sportframe Trailer Hitch Receiver part #24982, not the Draw-Tite Sportframe Trailer Hitch Receiver part #24914 which is for a 2014 - 2018 Mazda 3 Hatchback. I have attached a photo for…

view full answer...

Answer 12

The 3-1/8 inches of rise that the Curt Class II Euro Style Drawbar #C45562 has is measured from the top of the shank to the beginning of the vertical bend below the ball. Check out the video I attached to see this measurement.

view full answer...

What is the Rise on Curt Euro-Style Ball Mount # 45562

Product Page this Question was Asked From

Continue Researching