Does Stromberg Carlson Trailer Hitch SC45MR Have Capacity for 3,000 lb Trailer

Question

Question:

Can I tow 3000 lbs. trailer with UTV if this is welded onto the frame of 2019 Rockwood 5th wheel RV?

asked by: Russ

0

Expert Reply:

Yes, if you install the Stromberg Carlson trailer hitch # SC45MR by welding it you'd have a 3,500 lb towing capacity which be more than enough to tow a 3,000 lb trailer.

expert reply by: Jameson C

0

Answer 1

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75282 requires all hardware be torqued to 68 foot pounds according to the instructions. I've attached a photo in case you need anything else for this…

view full answer...

Answer 2

The weight capacity of the Stromberg Multi-Fit hitch part #SC45MR is based on how you install it. If you weld it on it has a tongue weight capacity of 350 lbs and if bolted on 200 lbs. It is not rated for towing.

view full answer...

Answer 3

The only thing you'll need to verify is that the width of the frame on your 2020 Jayco Jay Flight is between 49-1/2" and 76-1/2" (reason being we have no way of knowing the exact width of any trailer frame). If it is, then…

view full answer...

Answer 4

Thanks for reaching out! I recommend checking out the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR for your travel trailer. Hitches like this are universal fits so you just need to make sure the frame of your trailer is in the…

view full answer...

Answer 5

The center to center measurement of the mounting bracket bolt-holes for the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR is 5-7/8". Additionally, there are two other bolts holes on the angle brackets that measure…

view full answer...

Answer 6

Yes, if you plan on bolting the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR on then you would need to drill holes in the adjustable arms in order to set them to the correct length. There aren't any predrilled so that this…

view full answer...

Answer 7

There aren't any front-mounted trailer hitch receivers that are custom designed to fit for a 1985 Dodge B350 and your bumper is not structurally strong enough to work with the Curt RV Bumper 2" Trailer Hitch Receiver #E-100. What that means…

view full answer...

Answer 8

The frame-mounted Curt Adjustable Width Trailer Hitch Receiver #13703 is your best option for adding a trailer hitch to your Lance 2185 trailer. This model is designed specifically for trailers like this and it can fit frame widths of 22 to 72…

view full answer...

Answer 9

The spacing from the top of the flat end bracket to the center of the hole on the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR (CC-300) is 1.5".

view full answer...

Answer 10

The receiver tube of the Stromberg Carlson Adjustable Accessory Hitch Receiver #SC45MR is going to stick out 4-11/16" past the crossmember and since both tubes are 2" x 2" the height from the bottom of the receiver tube to the top of…

view full answer...

Answer 11

My contact at Swagman advises that the back edge of the main 2 x 2 inch horizontal tube will extend back 16 inches from the center of the hitch pin hole on your receiver. I have included a measured drawing of this carrier that will help illustrate.…

view full answer...

Answer 12

The length of the center cross tube of the Curt Adjustable Width Trailer Hitch for RV #13703 is 68-1/2 inches. I've also attached a photo of the dimensions for the brackets to assist.

view full answer...

Does Stromberg Carlson Trailer Hitch SC45MR Have Capacity for 3,000 lb Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching