Does Install of Draw Tite Hitch for 2020 Mercedes Benz Sprinter Require Hitch Modification

Question

Question:

2020 sprinter 2500 144inch crew van 2wd gas with factory step number does exhaust need modified with the 75601?

asked by: Derrick

0

Expert Reply:

When installing the Draw Tite hitch part # 75601 that fits your 2020 Mercedes Sprinter 2500 144 inch wheelbase with step bumper you do not need to modify the exhaust. There's no drilling involved either.

expert reply by: Jameson C

0

Answer 1

If your 2019 Mercedes-Benz Sprinter 2500 has a standard bumper without the step, the Draw-Tite #75549 is going to provide you with the most ground clearance at 15" from the bottom of the receiver tube to the ground. If your Sprinter has the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 5

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Answer 9

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 10

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...

Answer 11

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 12

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...