Solution for Repair Kit for Fulton 11-300 1-7/8" Coupler For 3" Channel

Question

Question:

I am trying to purchase a repair kit for a Fulton 11-300 1 7/8 coupler. If you have one please send me part number. Thank you

asked by: Walter L

1

Helpful Expert Reply:

The Fulton 11-300 1-7/8" coupler was discontinued and, according to my contact at Horizon Global, repair kits are no longer available. The only solution is to replace the coupler. I recommend using the Channel Tongue Trailer Coupler # CT-2003-Z. This fits a 1-7/8" ball, a 3" channel tongue, and has the same 2,000 lb capacity.

expert reply by: Robin H

1

Answer 1

I went to the warehouse to take the measurement you were asking about and found the distance from the top to the side holes on coupler #CT-2003-Z to be almost 1 inch exactly.

view full answer...

Answer 2

The closest we come to the 2-1/2 inch center to center measurement of the mounting holes you have on your coupler and trailer are 2-1/4 inches, just as you said you have found. The trailer coupler I recommend is part #CT-2002-Z. This is a 2,000-lb…

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 9

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Solution for Repair Kit for Fulton 11-300 1-7/8" Coupler For 3" Channel

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching