CT-2003-Z Trailer Coupler Measurement From Top to Side Holes

Question

Question:

What is the vertical distance from the top latch surface to the side holes? The corresponding dimension in my current channel is 1-1/4 inches so I need a minimum distance of 1-3/8 inches assuming material thickness of .100 inches.

asked by: Bob W

0

Expert Reply:

I went to the warehouse to take the measurement you were asking about and found the distance from the top to the side holes on coupler # CT-2003-Z to be almost 1 inch exactly.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The closest we come to the 2-1/2 inch center to center measurement of the mounting holes you have on your coupler and trailer are 2-1/4 inches, just as you said you have found. The trailer coupler I recommend is part #CT-2002-Z. This is a 2,000-lb…

view full answer...

Answer 2

The Fulton 11-300 1-7/8" coupler was discontinued and, according to my contact at Horizon Global, repair kits are no longer available. The only solution is to replace the coupler. I recommend using the Channel Tongue Trailer Coupler #CT-2003-Z.…

view full answer...

Answer 3

There is a couple of way to determine which wheel bearings and grease seals you will be needed for a trailer axle. First, checking the numbers on the wheel bearings and seal will allow you to select the correct parts for your axle. However, in some…

view full answer...

Answer 4

From center to center, the distance between the two side bolt holes on #CT-2003-Z is 2-1/4". On #DL13728 the distance is 3". Both trailer couplers fit a 3" channel tongue, a 1-7/8" ball and are rated at 2,000 lbs. If you are…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

CT-2003-Z Trailer Coupler Measurement From Top to Side Holes

Product Page this Question was Asked From

Continue Researching