Replacement Fan Blade For An Advent RV Air Conditioners

Question

Question:

I am looking for fan blade for air conditioner for Cherokee 2012, RV

asked by: Hector A

0

Expert Reply:

In order to find the correct replacement fan blade for your 2012 Forest River Cherokee, I am going to need to know what you have in your trailer currently.

For instance, if you had the Advent Air RV Air Conditioner # ACM135, then you could use the:

-Replacement Fan Blade for Advent Air RV Air Conditioner # PXX128050095.

This fan blade will also fit the: # ACM135B, # ACM150, and # ACM150B.

If you let me know what air conditioner you have currently, I'd be happy to see if we have something for you.

expert reply by: Bryce D

0

Answer 1

That Advent Air replacement fan blade is no longer available but we do have the part #PXX128050095 which is the current fan blade replacement for Advent Air AC units and would be what you would need.

view full answer...

Answer 2

Yes, the Replacement Fan Blade for Advent Air RV Air Conditioner part #PXX128050095 will fit a Advent Air RV Air Conditioner part AC135/ACM135 as it's the same unit.

view full answer...

Answer 3

ASA Electronics couldn't say if their #PXX128050095 replacement fan would work on a Carrier AC unit. I can provide you with the measurements you had asked for, though. The fan would indeed be compatible with a 1/2 inch shaft that has a flat…

view full answer...

Answer 4

Yes, the Replacement Fan Blade for Advent Air RV Air Conditioner item #PXX128050095 will fit the Advent A/C ACM150SP.

view full answer...

Answer 5

Based off your description I believe you're talking about the "Blower Wheel" which can be replaced with part #ADV49FR. The fan blade on your Advent Air RV Air Conditioner #ACM150 can be replaced with the Replacement Fan…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...