Do Different Timbren Axle-Less Suspension Systems Have the Same Camber and Ride Height

Question

Question:

If you wanted to mix a Timbern 4inch 2000 lb without brakes and a Timbern 4inch 3500 lb with brakes is it an exact match as far as attaching to the trailer frame and it being aligned with caster and camber as well as ride height?

asked by: Sean C

0

Expert Reply:

The caster and camber could be the same on the # TASR35HDS03 and # ASR2KHDS05. The system has a slight manufacture camber. However, it is up to you on how much camber you have based on the installation. This can be changed using the included shims.

As far as the ride height is concerned, these do not have the same dimensions. This will result in a different height between the systems when installed. The # TASR35HDS03 will also stick out farther.

Since there is no real advantage to using two different systems I would recommend choosing two of the same capacity. If you choose to use the # ASR2KHDS05 you could use # AKHD-545-35-EZ-K for the hub and drum assembly, # AKEBRK-35-SA for brakes, and # AKIHUB-545-35-K for an idler hub on the pair without brakes.

The # TASR35HDS03 uses 6,000 lb hub and drum assemblies so you would need different parts. I recommend the # AKHD-655-6-EZ-K, # AKEBRK-6, and # AKIHUB-655-6-EZ-K for this setup.

expert reply by: Robin H

0

Answer 1

I do have a solution, but we do not carry any replacement torsion axles. What I can offer is the Timbren Axle-Less Trailer Suspension System - Spindle w/Brake Flange - Regular Tires - 2,200 lbs #ASR1THDS01. This is a complete axle and suspension…

view full answer...

Answer 2

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 3

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

The Timbren Axle-Less Trailer Suspension #ASR2KHDS09 you're looking at is actually not going to work with your trailer tires since this kit is only going to work with trailer wheels that are 16" or larger. So, instead I'd recommend going…

view full answer...

Answer 8

Thanks for the picture of the a-frame jack mounting bolt hole dimensions you have. Based on that we know you have a standard jack mount on your trailer and the Stromberg Carlson Electric Trailer Jack #JET-5000 you are interested in is a confirmed fit…

view full answer...

Answer 9

When it comes to the wiring for the Dexter Electric Over Hydraulic Brake Actuator, #K71-651: 1. The black wire will connect to the 12V circuit coming from the vehicle's trailer wiring that is always hot. 2. White is the ground. 3. The yellow wire…

view full answer...

Answer 10

The Timbren Heavy-Duty Axle-Less Trailer Suspension - 4" Drop Spindle - Regular Tires - 2,000 lbs #ASR2KHDS05 are very popular, so we try to keep them available. The idler hubs I recommend that are compatible are the Trailer Idler Hub Assembly…

view full answer...

Answer 11

The Phoenix Electric Trailer Jack with Remote #UF38-944055 has a multiple mount hole pattern. This pattern allows you to position the jack so the motor faces the front of the A-Frame, or it can be rotated so that the motor faces the drivers side of…

view full answer...

Answer 12

In order to find the correct lift kit for your 2023 Riverside Retro 135 Camper, you'll first need to start by identifying the axle. If the trailer uses leaf spring axles then that makes things easy as your options are either an axle flip kit or…

view full answer...

Do Different Timbren Axle-Less Suspension Systems Have the Same Camber and Ride Height

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching