Fitment of Curt RV Bumper Hitch for Jayco Jayfeather Travel Trailer

Question

Question:

Will this fit a 2011 Jayco jayfeather 199 bumper?

asked by: Eric G

0

Expert Reply:

The Curt RV Bumper Hitch, # C19101 will fit 4 x 2 Inch RV bumpers. We do not have the ability to pull OEM build sheets and identify what part numbers where used when constructing your travel trailer. But if you have a 4 x 2 inch bumper this will fit. If you have a 4 x4 inch bumper, you will want to select the Curt RV Bumper Trailer Hitch, # E-100.

expert reply by: Michael R

0

Answer 1

From what I can tell of the photos I saw it looks like your 2018 Jayco Jay Feather has a square tube bumper. If it does, and that bumper is a 4" square bumper the correct trailer hitch receiver is the Curt RV Bumper 2" Trailer Hitch…

view full answer...

Answer 2

My first suggestion would be to contact your Jayco in order to determine if they recommend using a hitch on the rear of your 2005 Jayco JayFeather M-19H. You will want to provide them with your VIN for the most accurate information. If they ok the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Answer 11

Hey George, thanks for reaching out! As long as you aren't towing more than the 3,400 lbs I recommend using the Hidden Hitch by Draw-Tite Trailer Hitch Receiver #DT82GR for your 2023 Volvo XC60 because of the completely removable hitch receiver…

view full answer...

Answer 12

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...