Replacement Heating Pad For Thomas Payne Furniture

Question

Question:

So you can not replace heating pad on leather recliner

asked by: Charles C

1

Helpful Expert Reply:

We do have some replacement heating pads for your Thomas Payne recliner's. Depending on what series you have, we may have a solution for you.

If you have the Thomas Payne Theater seating, # LC38UD will work for you.

If you have the Seismic Series RV Couches, then # 674864 will work for you if you have reclining functionality.

expert reply by: Bryce D

1

Answer 1

If your Thomas Payne recliner has the power recline function, then the 29 volt, #674864 is the correct heating pad replacement. If not, then the Replacement 12 Volt Seat Heating Pad for Thomas Payne RV Theatre Seating #LC38UD is the correct…

view full answer...

Answer 2

I apologize for your issues with your heating pads! The Replacement 12 Volt Seat Heating Pad for Thomas Payne RV Theatre Seating #LC38UD is the same pad as the 354491. The 354491 is the Lippert part number and the #LC38UD is the part number here at…

view full answer...

Answer 3

The replacement part you need is the Replacement 12 Volt Heating Pad For Thomas Payne RV Theatre Seating, part #LC38UD. I have included a product description link below.

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Replacement Heating Pad For Thomas Payne Furniture

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching