Differences Between Available Trailer Hitches for 2020 Chevy Blazer
Question:
What's the diff between the Curt and Drawtite hitches for 2020 Chevrolet Blazer? Not sure which to get.
asked by: Rodrigo P
Expert Reply:
The major differences between the Curt # C13418 and the Draw-Tite # 76023 are the hitch capacity, the way they install and the difficulty of the installation.
The Curt hitch has a 5000 lb towing/750 lb tongue weight capacity, while the Draw-Tite has a slightly lower capacity at 4500 lb towing/675 lb tongue weight.
Both hitches install so that the receiver extends through the removable panel in the bumper, but the Curt installs from underneath, and will take about 40 minutes for a professional installer, while the Draw-Tite would require that the bumper cover and bumper beam be temporarily removed, and would take a pro about 2 hours to install.
I'd recommend the Curt # C13418 due to its slightly higher capacity and much easier installation.
If you'll be towing with the hitch, you'll need a trailer wiring harness like # 118720 for a 4 pole or # 118276 for a 7-way. For a ball mount, use # 2753 and # 19260 for a 1-7/8 inch or # 63845 for a 2 inch trailer ball.
I've linked to installation videos for the hitch and wiring mentioned above.
Products Referenced in This Question
T-One Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 7 Round - Blade
- Tekonsha
more information >
T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 4500 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Hub And Drum Replacement for 90865 Rockwell Hub and Drum
- Article: Trailer Maintenance Schedule
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Trailer Wiring Diagrams
- Q&A: Replacement Roof Vent Cover for Lid Marked AS-13M-VDO449 ANS Z26 1
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Q&A: Troubleshooting 6 Gallon Atwood Water Heater Not Working on Electric But Works on LP
- Q&A: Location of Heating Element on Atwood GC6AA-10E Water Heater
- Q&A: Should the Tires Lift Off the Ground While Leveling With the Lippert Ground Control Leveling System
- Q&A: Best Weight Distribution for a V-Nose Trailer with Short Frame Distance from Coupler to Body
- Article: My Trailer Hitch Doesn't Fit
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Roadmaster Vehicle Specific Base Plates
- Article: How to Choose a Battery Charger