Diameter of Center Hole of Wheel Retaining Ring # 33-52-1

Question

Question:

What is the diameter of the center hole on the 8 lug wheel retaining ring?

asked by: Jeffrey B

1

Helpful Expert Reply:

We were able to find the diameter of the center hole for you of the Wheel Retaining Ring # 33-52-1.

As you can see by the accompanying diagram, the diameter of the inner center hole is 5-15/16 inches.

I have added a link below to a video review for you to check out as well of the Wheel Retaining Ring # 33-52-1.

expert reply by: Kyle S

1

Inner Diameter of Retaining Ring # 33-52-1
(click to enlarge)

Answer 1

It looks like you recently purchased some Kodiak Wheel Bolts #K58WB316 and 5/8" flange nuts #95188 from us, so thank you for being a loyal customer! What you'll want to torque those to will depend on the construction of your wheels and the…

view full answer...

Answer 2

The D1012 is a Dexter 10,000 lb axle, so it'll have 10,000 lb Dexter electric brakes like the Dexter Electric Trailer Brake Kit #23-438-439. Many do not work, as they do need specific brake magnets, and the correct replacement brake magnets for…

view full answer...

Answer 3

You need the Wheel Retaining Ring #33-52-1 for your 10K axles and wheels. This ring has the single tab and will allow you to use your current flat faced wheel with Coned Lug Nuts #6-109. The retaining ring will sit outside the the wheels(see image).…

view full answer...

Answer 4

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 5

The retaining tab on the Wheel Retaining Ring #33-52-1 will need to be installed facing out so that the taper of the ring matches the lug nuts. Attached is a product overview video for you to check out as well.

view full answer...

Answer 6

The trailer tire and wheel combo to fit your 10K Dexter axle would be the Taskmaster Provider ST235/85R16 Trailer Tire with 16" Vesper Silver Dual Wheel, #TA45FR. This wheel can be used as either the inner or outer wheel of a dual-wheel setup.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Diameter of Center Hole of Wheel Retaining Ring # 33-52-1

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching