No Power on 12-Volt Pin at Trailer Connector on 2011 Chevy Silverado
Question:
I have a 2011 silverado I’ve already connected both wires under the hood to the posts at the distribution box and replaced / installed a new 40 amp and 30 amp fuse I should be able to get power now based on my knowledge and what I have read. Well my reason for the question is because I don’t have power What would be the next steps in diagnosing my problem?
asked by: John T
Expert Reply:
It sounds like you're not getting power at the pin in the 1:00 position in the trailer connector.
If you've installed new fuses and attached the wires at the distribution box under the hood, at this point I'd just abandon that feed and run the circuit directly to the positive battery terminal using a length of # 10-1-1 wire, a # 9510 circuit breaker and 2 # 44-5310A small ring terminals and one # 44-5356A large ring terminal. At the rear of the vehicle, find the wire feeding the pin in the 1:00 position in the 7-way trailer connector, cut the wire and connect the wire exiting the 7-way into the wire that you ran from from the battery.
Products Referenced in This Question
Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 3/16 Inch Diameter
- 12-10 Gauge
- Flint Hill Goods
more information >
Ring Terminal - 12-10 Gauge Wire - 5/16" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 5/16 Inch Diameter
- 12-10 Gauge
- Flint Hill Goods
more information >
40 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Twist-in, 7-Pole, RV-Style Trailer Connector for Chevy and GMC Vehicles - Vehicle End
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 7 Round - Blade
- Pollak
more information >
Continue Researching
- Q&A: No 12 Volt Power At 7-Way on 2008 Chevrolet Silverado To Charge Trailer Breakaway Battery
- Q&A: Location of Fuses In Power Distribution Box To Install Brake Controller on 2008 Chevrolet Silverado
- Q&A: Troubleshooting No 12 Volt Power at 7-Way Trailer Connector on a 2009 Chevy or GM Duramax Pickup
- Article: Trailer Wiring Diagrams
- Shop: Replacement Custom Multi-Tow 7-Way and 4-Way Trailer Connectors
- Shop: Twist-in, 7-Pole, RV-Style Trailer Connector for Chevy and GMC Vehicles - Vehicle End
- Video: Hopkins Endurance Fifth Wheel Wiring Harness Installation - 2015 Chevrolet Silverado 2500
- Video: Pollak Twist-In Trailer Connector Installation - 2009 Chevrolet Silverado
- Search Results: 5th wheel bed plug
- Search Results: in bed trailer plug
- Search Results: 7 way in bed plug
- Shop: Trailer Wiring
- Q&A: What Connector is Needed For 2009 Chevy Silverado With Trailer Towing Wiring To The Bumper
- Q&A: Is There A Fuse To Power Trailer Brake Controller Port In 2021 Ford E-450 Cutaway Chassis?
- Q&A: Removing the 7-Way Trailer Wiring Plug from the Housing, 2010 Chevy Silverado with Factory 7-Way
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Shop: Go Power Retreat Solar Charging System with Digital Solar Controller - 100 Watt Solar Panel
- Shop: Zinc Plated Hex Flange Nut - M8
- Video: Trailer Brake Controller Installation - 2014 Chevrolet Silverado 1500 3016
- Q&A: 7-Way to Replace Rusted OEM Bracket on 2007 Chevy Silverado
- Article: Brake Controller Installation for 2007 (New Body Style) - 2013 GMC Sierra and Chevy Silverado
- Shop: Hook Probe Circuit Tester
- Shop: Trailer Hitch
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Video: Choosing the Right Brake Controller
- Search Results: 68149
- Search Results: 25580