What Gauge Wire Does Mighty Cord # A10-5050D90VP Use

Question

Question:

What gauge wire is used in this adapter? I heard its only 10. That is not 50amp compatable.

asked by: Gary B

0

Expert Reply:

In short runs like what the # A10-5050D90VP has 10 gauge wire can be used for 50 amps. Normally it's recommended to go with 6 gauge when using a longer setup.

expert reply by: Jameson C

0

Answer 1

The distance between each of the mounting holes on the Mighty Cord Replacement RV Power Inlet is 2-7/16", as you can see in the accompanying photo. This inlet comes in your choice of either Black #A10-50INBKVP or White #A10-50INVP.

view full answer...

Answer 2

Yes, you do have the right adapter for the Epicord 50 Amp Twist Lock Power Inlet #277-000139. To plug into the inlet and parallel kit you can absolutely use the Mighty Cord 90-Degree RV Power Cord Adapter - 50 Amp Twist Lock Female to 50 Amp Male…

view full answer...

Answer 3

I spoke to my contact at Valterra and she confirmed that the Mighty Cord RV Power Cord Extension w/ Indicator Lights - 50 Amps - 50' Long #A10-5050EHLED is made of copper wiring.

view full answer...

Answer 4

You can hook up your 50 amp RV to a 30 amp power source so long as you have an adapter like the Mighty Cord RV Power Cord Adapter - 50 Amp Female to 30 Amp Male #A10-3050FHVP. Since you mentioned you are using an adapter you can do this and…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 10

Yes, in order to set your trailer up for use with shore power you will first need an AC distribution panel. For this, I recommend a Progressive Dynamics Series AC Distribution Panel. In order to bring power into the panel you will also need a power…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

What Gauge Wire Does Mighty Cord # A10-5050D90VP Use

Product Page this Question was Asked From

Continue Researching