What is the Mighty Cord RV Power Cord Extension w/ Indicator Lights # A10-5050EHLED Made With

Question

Question:

Hi. Is the Mighty Cord RV 50-amp 5- feet extension # A10-5050EHLED made with 100 copper wire? I could not find any indication as to what kind of wire this cord contains. Thanks!

asked by: Paula

0

Expert Reply:

I spoke to my contact at Valterra and she confirmed that the Mighty Cord RV Power Cord Extension w/ Indicator Lights - 50 Amps - 50' Long # A10-5050EHLED is made of copper wiring.

expert reply by: Thomas M

0

Answer 1

In short runs like what the #A10-5050D90VP has 10 gauge wire can be used for 50 amps. Normally it's recommended to go with 6 gauge when using a longer setup.

view full answer...

Answer 2

It sounds like you already have a 50 foot power cord for your RV to hook up to shore power, the Epicord RV Power Cord with Handle - 50 Amp Male to Twist Lock Female Connector - 50' Long #277-000157. There is a simple solution to this by adding…

view full answer...

Answer 3

The Mighty Cord RV Power Cord Item #A10-5025ED90 is not available in a 50 ft. Since you are wanting 50 ft for your 2019 Cardinal 3850 5th Wheel, I recommend using the Mighty Cord RV Power Cord Adapter Item #A10-5050D90VP with the Mighty Cord RV…

view full answer...

Answer 4

The Mighty Cord RV Power Cord Extension w/ Indicator Lights #A10-5050EHLED is a 4 wire cord comprised of 6 AWG wire and 8 AWG wire.

view full answer...

Answer 5

Yes the 50 foot long 50 amp power cord extension part #A10-5050EHLED that you referenced would work great for your application. It is the correct amperage rating, has the right connectors, and is 50 feet long.

view full answer...

Answer 6

That is correct. There is nothing to support the bumper when you install the Curt Hitch item #C15398 on a 2013 Toyota Tundra. That hitch was designed for the trucks without the factory hitch so there's no reason for it to have built in support…

view full answer...

Answer 7

You can hook up your 50 amp RV to a 30 amp power source so long as you have an adapter like the Mighty Cord RV Power Cord Adapter - 50 Amp Female to 30 Amp Male #A10-3050FHVP. Since you mentioned you are using an adapter you can do this and won't…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What is the Mighty Cord RV Power Cord Extension w/ Indicator Lights # A10-5050EHLED Made With

Product Page this Question was Asked From

Continue Researching