2012 Grand Vitara License Plate Holder with rear mounted spare
Question:
Will the left mounted license plate holder interfere with 13001 hitch? The instructions only mentions a small slot cut in the facia.
asked by: David M
Expert Reply:
According to Curt, the fascia mounted license plate holder of your 2012 Grand Vitara will not interfere with the installation of the # C13001 Class III receiver. Fascia trimming is only required on Grand Vitara models that have the spare tire under the vehicle, not on the rear hatch.
If you were planning on using the hitch for towing purposes, you might need the following to complete your towing system:
Ball Mount, part # D-4
Hitch Pin and Clip, # PC3
Trailer Wiring Harness, part # 56002
2 Inch Trailer Ball, part # 19247
1-7/8 Trailer Ball, part # 19260
Locking Hitch Pin, part # e98882
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 2" Hitch - Flush - 2-5/8" Span - Stainless Steel
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Stainless Steel
- Fits 2 Inch Hitch
- Flush Pin
- 2-5/8 Inch Span
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Installation of Trailer Hitch and Wiring on a 2008 Suzuki Grand Vitara
- Q&A: Does Stromberg Carlson Trailer Hitch SC45MR Have Capacity for 3,000 lb Trailer
- Q&A: Do Holes Need To Be Drilled Into The Adjustable Arms Of The Stromberg Carlson Adjustable Hitch
- Q&A: Does The Draw-Tite Trailer Hitch Receiver # 75448 Use all Mounting Holes 2012 Suzuki Grand Vitara?
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Can 2015 Ford Edge Tow 3500-Lb Trailer
- Q&A: What Is the Proper Oil for Oil Bath Hubs on Trailer Axles?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose a Bike Rack for a Motor Home or RV
- Article: What is an RV-Approved Bike Rack? (And Do You REALLY Need One?)
- Article: Best Bike Racks for Electric Bikes
- Article: How to Choose the Right Trailer Hitch Class