How to Convert Trailer Drum Brakes Over to Disc Brakes
Question:
I read your expert answer here: https://www.etrailer.com/question-7777.html My trailer has a set of Tie Down 12 LH/RH 11018/11019 drum brakes with a Tie Down model 66 surge actuator. Boat and trailer GVWR is 5200lbs with 15x6 rims. At least one of the drums is leaking brake fluid. I have been told the least expensive way to repair this is replacing the brake assembly with the Dexter part numbers above. I would like to explore the option of converting to Disc Brakes. Dexter tells me I need an entire kit with a Disc Actuator 82406. Your expert answer suggests the is a locking valve I could remove from my drum actuator and re-use the actuator for disc brakes maybe Dexter 82092 brake kits. Can you please help me find a more cost effective way to cover to disc brakes on my boat trailer?
asked by: Ron P
Expert Reply:
There is a good way to get the check valve out of your current actuator and save some money. What you will need to do is remove the large snap ring from the front of your actuator where the brake line attaches, pull the spring out, and at the end of the spring there will be a metal check valve. If you remove that check valve and reassemble the brake assembly without it you will be ready to use disc brakes.
Or a less invasive way is to puncture the check valve, basically you would just run a skinny ice pick or other sharp rod down the back opening of the actuator and then puncture the check valve and you would be ready to go.
Check out the video I attached that shows how to remove the check valve that Jameson did here at etrailer.
From there you can use the Kodiak Disc Brake Kit part # K2HR35D for each axle and the HydraStar Hydraulic Brake Line Kit part # HS496-252 to get the fluid from the actuator back to the disc.
Products Referenced in This Question
Hydrastar Hydraulic Brake Line Kit - Tandem Axle - 25' Long, 3/16" Main Line
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Disc Brakes
- Hydraulic Drum Brakes
- 25 Feet Long
- Brake Lines
- Steel Line and Flexible Hose
- Brake Line Kits
- Tandem Axle
- Hydrastar
more information >
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Q&A: Will 3,500 lb Kodiak Disc Brake Kit Fit 2012 EZ Loader Boat Trailer
- Q&A: Trailer Hitch for 1995 Chevy G20 Van
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Q&A: Availability of a 5 on 4-1/2 Hub with a # LM11949 Outer Wheel Bearing
- Q&A: Do Trailer Tires and Wheels Need to be Balanced
- Q&A: Magnetek Series 6300A Model 6332 Replacement Converter
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Most Popular Wheel Bearings
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: Where to Position the Trailer Axle?
- Article: Adapters for Towing a 5th Wheel Trailer with a Gooseneck Hitch