Hitch Installation Instructions for 2012 Impreza Hatchback
Question:
You have this model #11317 listed as the correct hitch for 2012 Impreza Hatchback Premium, Single Exhaust. Can you tell me if the hitch is designed to use the knock-out hole in the middle of the plastic trim below the bumper, or will it hang visibly below that trim? Also, can you forward installation instructions, as I cannot fathom how I would access the back side of the bolt holes in the frame to bolt the thing to the car, and wouldnt want to purchase something I could not install? Thanks!!
asked by: Clif
Expert Reply:
For the 2012 Impreza Hatchback, the correct hitch would be the Curt # C11286. For WRX or WRX STi Hatchback models, the correct hitch would be # C11120. The # 11317 you mention is a fit for the WRX Sedan model only.
Of all the hitch manufacturers we deal with, I believe Curt does the best job on their installation instructions. I have linked you to the instructions for both hitches mentioned above. If you click the provided link, you can see a video showing the hitch being installed on a 2012 Impreza hatchback.
The bolts are threaded into the frame members using a bolt leader or fish wire, as shown in the instructions. I will link you to a video that shows the technique needed to use the bolt leader.
If you were planning on using the hitch for carrying a bike rack or cargo carrier, the use of a stabilizing strap # 18050 is required per Curt warranty requirements.
If you were planning on doing some light towing, you might also need the following:
Trailer wiring harness for Hatchback, part # 118573
1-7/8 inch trailer ball, part # 19256
2 inch trailer ball, part # 19258
Locking hitch pin, part # e98879
I have edited a photo showing how both of the hitches I mentioned would install in relation to the rear bumper on their respective vehicle. The C11286 would not utilize the cut out in the bumper, but would install under the bumper fascia as shown.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 1-1/4" Hitches - Flush - 2-1/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 1-1/4 Inch Hitch
- Flush Pin
- 2-1/8 Inch Span
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Trailer Wiring
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Shop: Performance Chip Tuners
- Article: How to Measure for Trailer Hitch Drop
- Video: Yakima Rack and Roll Trailer Review
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Q&A: Recommended Trailer Hitch Receiver for 2009 Subaru Impreza WRX Sedan with Dual Exhaust
- Shop: Edge Insight CS2 Comprehensive Gauge Display - Color Screen
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Video: Choosing the Right Trailer Wiring
- Q&A: No Power to Trailer Wiring Harness on a 2013 Subaru Outback
- Search Results: 45572
- Search Results: 1.25 hitch ball mount
- Search Results: 24959
- Search Results: locking hitch pin
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Hitch for 2009 Subaru Impreza WRX Hatchback That Fits with Aftermarket Exhaust
- Q&A: Trailer Hitch Fit for 2010 Subaru Impreza Outback Sport
- Video: Trailer Hitch Installation - 2009 Subaru Impreza - Curt
- Search Results: subaru hitch
- Q&A: Will Curt Trailer Hitch 11120 Fit a Base Model 2013 Subaru Impreza Hatchback with Single Exhaust
- Q&A: Is Trimming Rear Fascia of 2014 Subaru WRX Hatchback Required
- Q&A: Correct Curt Hitch for 2011 Subaru Impreza Hatchback with Single Exhaust
- Video: Curt Trailer Hitch Installation - 2010 Subaru Outback Wagon
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 44649
- Search Results: 68149