Does Same Hitch that Fits 2018 Nissan Rogue Fit 2018 Nissan Rogue Sport

Question

Question:

A 2018 Nissan Rogue Sport SL is a smaller size body than a standard Rogue and appears to have a different rear lower panel configuration , I.e. the absence of two lower panels shown removed for installing the hitch. 1. Does the installation for a 2018 Rogue Sport differ from that of a standard Rogue under carriage? 2. Do you have a video of install for a 2018 Rogue SPORT model? Thank you for your anticipated reply.

asked by: Ken D

0

Expert Reply:

Draw Tite makes a hitch specifically for the Sport SL models of the 2018 Nissan Rogue with the part # 76177 which is what you'd want over the # 75758 you mentioned.

I attached a picture of this hitch installed on a similar 2017 Nissan Rogue Sport as well as an install video for you to check out on the same vehicle that would show the same process as your 2018 model.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Draw Tite hitch part #75902 that you referenced would be the best option for your 2018 Nissan Rogue for carrying a bike rack. This is a 2 inch hitch that has a concealed crosstube which means you'll have a hitch with plenty of capacity…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

We do sell replacement hardware for all of the hitches we carry with the part #RHK but you might check down in the hitch tube to see if the hardware is taped up in there as that's sometimes where it's stored in shipping.

view full answer...