Boat Trailer Guide-Ons for 2 Inch Wide by 3 Inch Tall Trailer Frame

Question

Question:

Will CE27620 attach to trailer frame 2inch wide by 3inch high?

asked by: Keith H

0

Expert Reply:

The CE Smith # CE27620 Post-Style Guide-Ons will indeed fit your 2" wide x 3" tall frame member. The guide-ons will fit frame tubes up to 3" wide x 4-1/4" tall.

expert reply by: Mike L

0

Answer 1

Yes, you can use the CE Smith Post-Style Guide-Ons for Boat Trailers #CE27620 on your Multi Sport Trailer #CE48870. There won't be any clearance to attach them to the frame between the light and the fender, but they can be installed on the rear…

view full answer...

Answer 2

It sounds like you'll need to do some fab work in order to get the guide-ons to work. I believe your best bet would be to eliminate the u-bolts and have the brackets welded to the top or the underside of the frame member. If the fender step…

view full answer...

Answer 3

For your trailer frame channels that are 1-1/2 inches wide by 3 inches tall the mounting brackets of the CE Smith Post Guide Ons part #CE27620 would fit and work well.

view full answer...

Answer 4

Though it is possible to upgrade the wheels on the CE Smith Multi Sport Plus Boat and Kayak Trailer #CE48870 to a 13" option, like the Kenda Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel #AM31994, it will have to be a…

view full answer...

Answer 5

CE Smith Post-Style Guide-Ons for Boat Trailers #CE27620 are intended to provide only a visual guide for aiming your boat as you run it up onto the submerged trailer. They are not intended to make contact with the gunwales on each side of the boat to…

view full answer...

Answer 6

Post-Style Guide-Ons for Boat Trailers, like #CE27646 are designed to help you load your boat onto your trailer. Because the rear of the trailer is backed into the water, it makes it really hard to see if you're loading it straight onto the…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Boat Trailer Guide-Ons for 2 Inch Wide by 3 Inch Tall Trailer Frame

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching