Will Mounting Brackets of CE Smith Post Guide Ons Fit Shoreland'r Trailer Frame

Question

Question:

My ShoreLander trailer frame is 1 1/2inch wide by 3inch tall/deep. The comment states the inside dimension is 1 5/8. Will the hardware tighten well? Thanks,

asked by: John S

1

Helpful Expert Reply:

For your trailer frame channels that are 1-1/2 inches wide by 3 inches tall the mounting brackets of the CE Smith Post Guide Ons part # CE27620 would fit and work well.

expert reply by: Jameson C

1

Answer 1

Yes, you can use the CE Smith Post-Style Guide-Ons for Boat Trailers #CE27620 on your Multi Sport Trailer #CE48870. There won't be any clearance to attach them to the frame between the light and the fender, but they can be installed on the rear…

view full answer...

Answer 2

The CE Smith #CE27620 Post-Style Guide-Ons will indeed fit your 2" wide x 3" tall frame member. The guide-ons will fit frame tubes up to 3" wide x 4-1/4" tall.

view full answer...

Answer 3

Though it is possible to upgrade the wheels on the CE Smith Multi Sport Plus Boat and Kayak Trailer #CE48870 to a 13" option, like the Kenda Karrier ST175/80R13 Radial Trailer Tire with 13" Galvanized Wheel #AM31994, it will have to be a…

view full answer...

Answer 4

CE Smith Post-Style Guide-Ons for Boat Trailers #CE27620 are intended to provide only a visual guide for aiming your boat as you run it up onto the submerged trailer. They are not intended to make contact with the gunwales on each side of the boat to…

view full answer...

Answer 5

It sounds like you'll need to do some fab work in order to get the guide-ons to work. I believe your best bet would be to eliminate the u-bolts and have the brackets welded to the top or the underside of the frame member. If the fender step…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Will Mounting Brackets of CE Smith Post Guide Ons Fit Shoreland'r Trailer Frame

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching