Replacement Hardware Kit for Curt 13241 Hitch on 2015 Nissan Frontier

Question

Question:

I need replacement mounting hardware for hitch 13241 for a 2015 Nissan frontier. I cant find them on your website

asked by: Kevin M

0

Expert Reply:

I have a solution for you, but we do not have the individual hardware kits for each hitch built out within the site- there are just too many to list. In order to get the correct Replacement Hardware Kit # RHK , you'll simply go to the linked page for the RHK and select the manufacturer of the hitch, in this case it is a Curt. After that, you'll put in the part number of the Curt Hitch # 13241 where it says "Hitch Item Number". After you've done that, you'll just add the item to your cart and you're all set.

expert reply by: Erik B

0

Answer 1

The Curt hitch part #13241 that you referenced uses a total of 6 M12-1.25 x 35mm hex bolts and six 7/16 inch conical tooth washer. You would want to get grade 5 or higher bolts from your local hardware store. Since hitch hardware is considered one…

view full answer...

Answer 2

I would retap the threads with the next size up. Which from my research would be M12-1.5. If you are still unsure you can take the bolt you have with you to a hardware store, tell them you are in need of a tap that is the next size up, and they will…

view full answer...

Answer 3

If you have the hitch pin for the Reese Eclipse 4 Bike Rack part #63124 engaged enough so that the cotter pin can be inserted into the other side, then this will be sufficient in order to hold the shank inside of the receiver tube. That said, the…

view full answer...

Answer 4

In regards to the etrailer Trailer Hitch Receiver part #e98865 on your 2007 Pontiac Torrent, the first issue you are having with the weld nuts inside the bumper beam is most likely due to them being stripped. This would have most likely been caused…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Replacement Hardware Kit for Curt 13241 Hitch on 2015 Nissan Frontier

Product Page this Question was Asked From

Continue Researching