Trailer Coupler Latch is Very Difficult to Operate
Question:
We have a WDH set up by our dealer on our TV. When coupling we cannot get the latch to seat without extreme measures like jumping on bumper or towing forward and back. Also we cannot get the ball to release when decoupling. We need to actually pull the ball out of the TV receiver to unhitch. What can I adjust to remedy this. Thanks
asked by: Joe K
Expert Reply:
There are a few things that could be causing the issue you're experiencing.
Let's start with the obvious-be sure you're using the correct trailer ball for the coupler. The coupler will have the necessary ball size stamped into it. It may sound blatantly obvious, but hey, it happens.
Secondly, the nut on the underside of the latch can be used to adjust the tension of the latch to a degree. The latch/jaw mechanism of the coupler could be worn or damaged. We offer a few latch repair kits, which you can see by using the provided link. The coupler should have the manufacturer name and mode number stamped into it. A worn or damaged/deformed trailer ball could be at fault. Make sure the ball is still smooth and not gouged.
These are the most likely culprits, with the coupler being out of adjustment being the most likely.
Product Page this Question was Asked From
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Should Hitch Ball Angle Be Adjusted Up and Down or Angled to the Rear Using Weight Distribution
- Q&A: Adjusting Weight Distribution System to Apply More Weight to Front Axle of Tow Vehicle
- Shop: Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 6,000 lbs GTW, 600 lbs TW
- Q&A: Does A Weight Distribution System Need To Be Readjusted If I Lift My Truck
- Video: Fastway e2 Weight Distribution System Review
- Search Results: equalizer hitch
- Search Results: fastway e2 hitch
- Shop: Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 6,000 lbs GTW, 600 lbs TW
- Shop: Trailer Hitch
- Q&A: Installation Instructions for Curt 8000 lb Weight Distribution Hitch
- Q&A: How To Keep Hitch Ball From Spinning When Torqueing Nut
- Q&A: What Size Wrench is Needed for a 2" Hitch Ball with 1 Inch Diameter Shank
- Q&A: Does a Trailer have to be towed Level or Can it be Off Up or Down
- Search Results: 2 516 coupler
- Search Results: hitch coupler
- Search Results: trailer coupler
- Search Results: latch repair kit
- Search Results: coupler repair kit
- Shop: A-Frame Trailer Coupler - Thumb Latch - Black - 2-5/16" Ball - Weld On - 14,000 lbs
- Shop: Sleeve-Lock A-Frame Trailer Coupler - Flip Latch - Black - 2-5/16" Ball - 12,500 lbs
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 8,000 lbs GTW, 800 lbs TW
- Article: 5 Things to Know About Weight Distribution Hitches
- Shop: Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Top Load
- Article: How to Choose the Right Trailer Hitch Class
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams