How To Ground Trailer Tail Lights Without a Ground Wire To a Wooden Surface
Question:
I am installing on wood. How do I ground?
asked by: Stephen K
Expert Reply:
The Standard Trailer Light Kit with 25' Wire Harness part # TL29BK as I am sure you noticed grounds via the mounting hardware therefore there is not a singular ground wire. In order to attach this light to a wooden surface you will need to run a ground wire yourself up to the trailer tongue using the mounting studs on the back with ring terminals part # DW05705-1 and wire part # 12-1-1.
The other option you have is to use the Peterson LED Light Kit for Trailers part # V944 which does have a singular ground wire on each light. The side marker lights could then be added with the Optronics LED Clearance or Side Marker Light part # MCL36AB. This setup uses all LED lights which will last longer and draw less power than the above.
Products Referenced in This Question
Ring Terminal - 12-10 Gauge Wire - 3/8" Ring ID
- Wiring
- Wire Connectors
- Ring Terminals
- 3/8 Inch Diameter
- 12-10 Gauge
- Deka
more information >
Optronics LED Clearance or Side Marker Light w/ Reflex Reflector - 6 Diodes - Square - Amber Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Stud Mount
- Non-Submersible Lights
- LED Light
- 2-7/8L x 2-1/8W Inch
- Amber
- Optronics
more information >
Peterson LED Tail Light Kit for Trailers Over 80" Wide - 25' Harness - Driver and Passenger
- Trailer Lights
- Tail Lights
- License Plate
- Rear Clearance
- Rear Reflector
- Side Marker
- Side Reflector
- Stop/Turn/Tail
- Kit
- LED Light
- Red
- Peterson
more information >
Product Page this Question was Asked From
Standard Trailer Light Kit with 25' Wire Harness
- Trailer Lights
- Tail Lights
- License Plate
- Rear Reflector
- Side Marker
- Side Reflector
- Stop/Turn/Tail
- Square
- Kit
- Surface Mount
- Non-Submersible Lights
- Incandescent Light
- 5L x 4-1/2W Inch
- Red and Amber
- Optronics
more information >
Continue Researching
- Shop: Wheel Bolt, 1/2" x 1-5/8" with Right Hand Threads
- Shop: Aluminum Car Hauler Ramp Set - 72" x 14-1/2" - 6,000 lbs - Qty 2
- Shop: Peterson LED Tail Light Kit for Trailers Over 80" Wide - 25' Harness - Driver and Passenger
- Q&A: Recommended Hub and Drums for Motor Home Axle with 25580 Inner and LM67018 Outer Bearing
- Shop: LED Trailer Combination Tail Light - Submersible - 7 Function - 10 Diodes - Red Lens - Driver Side
- Shop: Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long
- Shop: LED Combination Tail Light for Trailers over 80" Wide - Submersible - Red - Driver Side
- Shop: Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Top Load
- Q&A: Ramp Recommendation for Loading Bobcat 331 Onto Trailer
- Q&A: Weight Capacity of Gen-Y Aluminum Loading Ramp Set 325-GH-R96
- Video: Buyers Products Trailer Wiring Junction Box Review
- Video: Gen-Y Hitch Aluminum Loading Ramps Review
- Video: Buyers Products Wiring 3375601100 Review
- Video: Race Ramps Trailer Loading Assist Ramps Review
- Q&A: What is the Difference Between Over 80 inch and Under 80 inch Trailer Tail Lights
- Q&A: Availability of Bearing Kit BK3-310 with Larger Inner Diameter Grease Seal
- Q&A: Lighting Requirements for Trailer that is over 80 inches in Width
- Q&A: Determining If We Have A Replacement For A Dayton Fayette 9254 Hub and Drum Assembly
- Search Results: cross reference for seals
- Search Results: seal cross reference
- Search Results: 205 75 r15
- Search Results: tire covers
- Search Results: peterson
- Article: Trailer Wiring Diagrams
- Video: Buyers Products Trailer Lights 337LB383P Review
- Video: Review of Peterson Trailer Lights - Tail Lights - M844L
- Video: Peterson LED Trailer Tail Light Review and Installation
- Search Results: side brackets
- Search Results: flush mount trailer lights