What Parts are Needed to Install a Trailer Brake Controller on a 1989 Mazda B2600 4WD
Question:
What kit do I need to buy to install this unit in this truck? Any instructions for the install. I am planning on buying from you soon. Just installed the 4 pole to 7 pole adapter I bought from you and now I need to do the controller. Thank you
asked by: Todd N
Expert Reply:
Since you already have the # 37185 installed, you will need to hardwire the brake controller to the vehicle and to the 7-Way. What you will need is about 25 feet of # 10-2-1, a 40-amp circuit breaker, # PK54540, a circuit tester, # PTW2993, and a 20-amp circuit breaker, # PK54520, or 30-amp circuit breaker, # PK54530. (Use the 20-amp breaker if the trailer has 2 to 4 brake assemblies and use the 30-amp breaker if the trailer has 6 to 8 brake assemblies.)
With all of these parts you will just need to follow the FAQ instructions and the video I have linked for you. The 7-Way has blue and black wires on it. The blue wire goes to the brake controller blue wire and the black wire goes to the positive battery terminal via a 40 amp circuit breaker.
The brake controller white wire will need to ground to the negative battery terminal. The black wire will attach to the positive battery terminal via the 20 or 30 amp circuit breaker. The red wire attaches to the cold side of the brake switch.
Products Referenced in This Question
Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Wiring
- Wire
- Jacketed Wire
- 2 Wire
- 10 Gauge
- Deka
more information >
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 20 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 20 Amp
- Pollak
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 30 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 30 Amp
- Pollak
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Replacement Hub for 2013 Wildwood 26TBSS Hub Drum with AL-KO 8700
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: How To Add a Fuel Tank To a Truck with 5th Wheel Hitch In Bed
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Q&A: Comparing the Curt Q20 and the Curt A20 5th Wheel Hitches.
- Q&A: Which Nev-R-Adjust Brake Assemblies for Load Trail 14K Dump Trailer
- Article: Best Camper Jacks
- Article: How to Choose the Right Trailer Hitch Class
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)