Troubleshooting Electric Trailer Brakes

Question

Question:

Trailer bakes will not work after harness replacement and pin setup. Actions to date: New trailer controler, progressive red light indicates good signal Test/inspect all fuses in Ram truck. Bought 7 pin tester, plug it in and all lights work fine and trailer brakes signal works as normal. Still no brakes. Profile 2016 doudge ram and 23ft double axle E- brake design Keystone ultra lite year 2015 less than 5 K miles used. QUestion: I used grease on ball socket once very hard to get on truck ball. Do I need conductive grease or ?? Please advise. And Thank you.

asked by: Mark L

0

Expert Reply:

Troubleshooting electric trailer brakes is much easier if you disconnect the trailer plug from the truck and test each side separately. The process is not complicated and you need only a few items.

I suggest starting on the trailer. You'll just need a well-charged 12V battery (the one in the truck will work fine unless you happen to have a fully-charged spare one laying around), a standard set of jumper cables like # HMBC0860 and two short lengths of wire. You will connect the jumpers to the battery and to the two lengths of wire. Then apply these two wire leads to the contacts on the trailer plug, the ones shown in the photo I linked for you. You should hear the magnets humming.

If not, check that your re-wiring has the various circuits arranged according to the RV standard format shown in the linked article. It could just be a matter of an incorrect pin assignment when the re-wiring was done. If you apply the battery power to each contact on the trailer's plug you'll eventually find the brake circuit if it is not connected to the correct pin location in the photo. This testing process also allows you to test each trailer light circuit too and this is a good idea while you have the jumper cables connected.

If any trailer circuits do not work you'll want to trace their wires looking for worn or cracked insulation or spots where the wires may be rubbing on the frame or suspension components.

If the trailer behaves correctly with the direct battery power then get a circuit tester like # PTW2992 and move to the truck. Again please refer to the linked article to see how the circuits on a 7-way vehicle socket are arranged. Have a helper set the brake controller to maximum power and boost and apply the manual lever while you test the brake circuit on the truck.

If you get no signal there then you know the issue is on the truck. Please let me know the results of your trailer test and I can give you next steps if needed.

expert reply by: Adam R

0

click to enlarge

Answer 1

The picture for determining bolt pattern is actually a little easier than maybe it seems. You just need to measure across the wheel like it shows and then count the amount of lug holes and that's all you need. So if it's 5 inches and…

view full answer...

Answer 2

For a shut off switch with the Bulldog Winch part #BDW10030 I'd recommend the switch part #BDW20248 which is rated for 500 amps and is very easy to use. This is a cheap insurance policy for your winch wiring so it would be a really great…

view full answer...

Answer 3

The Bulldog Winch part #BDW15020 would be a great option for your setup. This is a 4,400 lb 12 volt winch which uses a synthetic rope instead of a steel cable. It powers in and out and has a built in brake as well. The winch also moves at 19 feet…

view full answer...

Answer 4

I went out to the warehouse and pulled a CURT Trailer Hitch Electric Winch Mount Plate, #C31010, to measure it. From the back of the mounting plate to the center of the nearest hitch pin hole, it is 4-1/4 inches. -The distance to the center hole is…

view full answer...

Answer 5

Typically, we want a winch that will be used to load a car trailer to have a line pull capacity at least 50% greater than its. gross vehicle weight With that in mind, my recommendation is the Bulldog Winch Trailer Winch - Synthetic Rope - Hawse…

view full answer...

Answer 6

For the Curt winch mount, #C31010, or any of the similar mounts, you will need to compare the mounting pattern on the mount to what your winch requires. I have included 2 pictures. One shows the mount pattern of the Curt mount.

view full answer...

Answer 7

Yes, the Warn M8000 Winch uses a 10" x 4-1/2" mounting pattern which the Curt Trailer Hitch Electric Winch Mount Plate part #C31010 will accept so they can be used together just fine. The 10" x 4-1/2" mounting pattern is an…

view full answer...

Answer 8

Yes, the Superwinch Tiger Shark Series Off-Road Winch #SW1511200 that you referenced will fit the Curt Winch Mount part #C31010 that you also referenced. The winch has more capacity than the mount so you would have to stay under the 9k rating of the…

view full answer...

Answer 9

We can help you select the right electric winch for your car trailer that will be able to handle the vehicle's 3500-lb weight and the slope of your trailer's loading ramp. For reference I linked an article that has great helpful information…

view full answer...

Answer 10

I have a selection of front mount hitch mounting plates to choose from. I am including a link to a product page that will list the choices of mounting plates. Our most popular mounting plates for front mount hitch is the CURT Trailer Hitch Electric…

view full answer...

Answer 11

For mounting a winch to a trailer like the Superwinch #SW1455201 one solution is to weld a hitch tube to the trailer like with the part #E-9 so that you could use a winch mounting plate like the #BDW20011 and have a way to easily remove and reinstall…

view full answer...

Answer 12

The pre-mounted combinations of trailer wheels and trailer tires that we offer are given a degree of balancing by the distributor but not a full dynamic balance on a balancing machine as passenger car tires require. I will explain. Wheels and tires…

view full answer...

Troubleshooting Electric Trailer Brakes

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching