Ball Height for Pulling a 2016 Coachmen Clipper with a 2004 Honda Pilot
Question:
did you have ball hitch recommendation for a 2 5/16 size that works for that ball mount?
asked by: Ryan
Helpful Expert Reply:
You want the trailer to be as level as possibel when towing. To figure out the correct rise or drop you need with your 2004 Honda Pilot measure from the ground to the inside top of the trailer hitches opening with the vehicle parked on level ground. Then measure from the ground to the underside of the trailer's coupler with it level as well. The difference between the two tells you how much of a rise (the trailer is higher than the vehicle) or a drop (the vehicle is higher than the trailer) you need to tow level.
One way to take out some of the guesswork is an adjustable ball mount like part # MT70068. It provides up to 7-1/2 inches of drop or 6-1/2 inches of rise. For a ball that fits use part # 63845 for a 2 inch or part # 19260 for a 1-7/8 inch. You need the hitch ball to match the size of the trailer's coupler as well.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
2-5/16" Hitch Ball - 1" Diameter x 2-1/4" Long Shank - Chrome - 10,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-1/4 Inch Shank Length
- 1 Inch Diameter Shank
- 10000 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 7 Inch
- Rise - 6 Inch
- Fits 2 Inch Hitch
- 5000 lbs GTW
- Class III
- Long Shank
- MaxxTow
more information >
Continue Researching
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: Trailer Hitch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Shop: MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: Wiring Harness to Install Redarc Brake Controller in a 2017 Ram 1500
- Video: Curt Weight Distribution - WD With Sway Control - C17499 Review
- Search Results: fuse holder
- Search Results: ball
- Search Results: 7~way
- Search Results: boat trailer wire
- Search Results: fuse
- Search Results: breaker
- Search Results: 7 way trailer wire
- Shop: Replacement 17'1" Fabric for 18' RV Awning - Universal - Black Fade
- Shop: Deka Wire - Jacketed 7-Wire - per Foot
- Shop: Solera Smart Arm 12V Power RV Awning - 18' Wide - Programmable - Black Fade
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Q&A: Brake Controller and Trailer Wiring Setup for 1995 Dodge Ram 1500
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2019 Honda Odyssey
- Shop: RV Camera
- Video: Redarc Tow-Pro Liberty Brake Controller Installation - 2016 Ram 1500
- Video: Choosing the Right Brake Controller
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2019 Honda Odyssey
- Video: EcoHitch Hidden Trailer Hitch Installation - 2018 Honda Odyssey
- Q&A: Recommended Camera System to Monitor Trailer Tires During Travel
- Video: Redarc Tow-Pro Liberty Brake Controller Installation - 2019 Toyota Highlander
Ryan
7/16/2018
did you have ball hitch recommendation for a 2 5/16 size that works for that ball mount?