My Axle Has No Cotter Pin Hole Can I Install Bearing Kit for #84 Spindle?
Question:
I have a dexter 8-248 hub on a wells Cargo trl... bearings are L44649 and L68149. I see you have a kit bi my axle has no cotter pin hole. It has a bendable tab on spacer to go into castle but space. Is this kit still usable for me? Also need 2 ez lube caps.. they have a number of 85-1 on them
asked by: Rob C
Expert Reply:
The # BK2-100 Bearing Kit for #84 Spindle L44649/L68149 Bearings 10-19 Double Lip Seal will work. You have EZ Lube spindles which do not use a cotter pin. The spindle has a tube in it for the grease to be pumped in. Instead it uses a tang washer, which is the bendable tab on spacer you were referring to. Even the manufacturer said the # BK2-100 kit was designed for hubs that use the number 84 spindle.
This Kit comes with both a cotter pin for standard spindles and a tang washer for EZ-Lube spindles.
The lube caps you need # RG04-040 has a 1.99" outer diameter. I would encourage you to measure to make sure this is the size you need. I have attached the dimensions to this product.
Products Referenced in This Question
Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- E-Z Lube Grease Cap
- 1.99 Inch O.D.
- TruRyde
more information >
Product Page this Question was Asked From
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Shop: Trailer Valet JXS Drill Powered Drop Leg Trailer Jack w/ Footplate - Sidewind - Side Mount - 7K
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Replacement Spindle Washer - Tang Type for E-Z Lube
- Shop: Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate - Sidewind - 14" Lift - 2K
- Search Results: trailer jack
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Shop: Spindle Nut Kit for EZ Lube Axles
- Video: Bulldog A-Frame Sidewind Round Jack Review
- Search Results: dexter tang washer
- Shop: Replacement Spindle Nut for Dexter Nev-R-Lube Hub and Drum Assemblies - Qty 1
- Video: TryRyde Tang Type Replacement Spindle Washer Review
- Search Results: trailer step
- Search Results: solera xl
- Search Results: ventmate
- Search Results: vent
- Search Results: powered vent
- Q&A: Recommended Replacement For A Magic Chef MCD990ARB RV Microwave
- Q&A: Method for removing and Installing Tang-Style Spindles Washers
- Video: etrailer Trailer Idler Hub Assembly Installation
- Article: Most Popular Wheel Bearings
- Video: Kodiak Trailer Brakes 20TA-BLKIT Review
- Video: DeeMaxx Disc Brake Kit Review
- Video: Redline Trailer Spindles RG05-100 Review
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Q&A: Spring Keeps Falling Out of Bulldog Collar-Lok Trailer Coupler
- Q&A: How to Paint the Bulldog Weld On Coupler.
- Q&A: Trailer Coupler is Stuck on Hitch Ball and Will Not Release
- Q&A: Is Sleeve-Lock A-Frame Trailer Coupler # CA-5196-B Designed for Weld On 50 Degree A-Frames
- Q&A: Why Would a Trailer Hitch Come Detached From the Ball During Travel?
- Shop: Performance Chip Tuners