Updated Servo for the Pewag Servo RS Self-Tensioning Snow Tire Chains

Question

Question:

Hi, is this the most current model for these chains? the servo switching mechanisms looks like it might be different on the pewag website for the servo RS. that is, instead of the previous older black module with a single red switch Ive attached a pic, it looks like there might be a newer model with a module that has a red wheel edge on each side rather than just one red tab. Id like to get the newest model year available. can you check on this for me? thanks,

asked by: Tom

0

Expert Reply:

The servo included in the Pewag Servo RS Self-Tensioning Snow Tire Chains part # PWRS80 is the most up to date servo offered from Pewag at this time. The servo you have is the old version which was redesigned because of mud entering the device and creating functionality issues. The hole that was allowing mud to enter the old servo has since been phased out.

As long as you have one of the following tire sizes then the above tire chains will work well for you. If you have a different tire size not listed below please let me know what that is and I would be glad to recommend the correct set for you.

215/75-17.5
215/85-16
235/60-18
235/65-17
235/70-17
245/60-18
245/65-17
255/70-15

I have attached an installation video of the above tire chains for you as well.

expert reply by: Conner L

0

click to enlarge

Answer 1

All of our tire chains that fit your tire size 245/60-18 appear on the linked page. In the manual for your 2017 Honda Pilot (page 609) Honda recommends using lower-profile S-Class chains. This is a common requirement for passenger vehicles and we…

view full answer...

Answer 2

I recommend going with the Pewag Servo RS #PWRS80 for the 235/60-18 size tires on your 2019 Honda Odyssey because these feature a drape-over installation, steel square links in a diamond pattern, rim protection, and a quick release for easy removal.…

view full answer...

Answer 3

For your 2017 Honda Odyssey the Pewag Servo RS Self-Tensioning Snow Tire Chains #PWRS80 fit both of the common tire sizes for your vehicle of 235/60-18 and 235/65-17. These are easy to install, provide great traction, and offer great tire clearances…

view full answer...

Answer 4

I looked up the tire size of your Subaru Outback 2019 Touring and found it to be 225/60-18 so for a tire chain set that matches what you are looking for the best option is the Pewag Servo RS part #PWRSV79 which we had the chance to install on a 2019…

view full answer...

Answer 5

With the Pewag Servo RS Self-Tensioning Snow Tire Chains #PWRS80 you do not need to use any additional tensioners beyond what comes with them. These chains self-tension which means no other additional tensioners are needed. For more info on these…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Updated Servo for the Pewag Servo RS Self-Tensioning Snow Tire Chains

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching