Welding Ultra-Fab Hitch to I-Beam Frame and Length of Receiver
Question:
What is the weight of the Ulta-Fab 2 inch hitch? Also you state the hitch works on all types of frames but the instructions just shows a box frame, help me to understand how the mount welds to an I frame? Also what is the measurement from the back of the 2 inch cross member tube to the end of the 2inch receiver, in other works how far does the receiver extend toward the back of the RV? I own a 2006 Keystone Montana 5th wheel and the hitch will be used to carry 2 bikes in a RV approved bike carrier The Curt bolt on hitch is to low and the bracket is to wide for my 5th wheel and is over kill for 2 bikes. Thank You
asked by: Michel S
Helpful Expert Reply:
The Ultra-Fab Hitch # UF35-946403 weighs 50 lbs; I went to the warehouse to measure how far the receiver extends away from the tube and found it to be approximately 5-3/4".
As for how the Ultra-Fab welds onto an I-beam frame I contacted the manufacturer and was told that in order to do this, gusset plates would need to be fabricated and used by the installer. Should you also be in need of a bike rack, I have added a link to the racks we carry which are approved for use with an RV.
Product Page this Question was Asked From
Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames
- RV and Camper Hitch
- Frame Mount Hitch
- 47 - 77 Inch Wide Frame
- 350 lbs TW
- 2 Inch Hitch
- Weld-On
- Ultra-Fab Products
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Installation Of Ultra-Fab 2 Inch Trailer Hitch Receiver For Trailer Frames
- Shop: Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Shop: Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames
- Video: Ultra-Fab Products RV and Camper Hitch - Frame Mount Hitch - UF35-946403 Review
- Shop: Mount-n-Lock GennyGo Generator and Cargo Carrier for RV Bumpers - Steel - 200 lbs
- Shop: Adjustable Width Trailer Hitch Receiver for RVs, 18" to 51" Wide
- Video: Hollywood Racks RV Rider 2 Electric Bike Platform Rack Review
- Q&A: Mounting Dimensions of the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames Part # UF35-946403
- Shop: Kuat Transfer V2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Wheel Mount
- Shop: Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Shop: Hollywood Racks Sport Rider SE2 Bike Rack for 2 Bikes - 2" Hitches - Frame Mount
- Q&A: E Bike Rack Recommendation for 70 lb Bike
- Search Results: hollywood racks
- Q&A: Measurements Of Ultra Fab RV Trailer Hitch Mounting Plate That Welds To The Frame
- Q&A: Where Does Ultra-Fab Trailer Hitch # UF35-946403 Weld to an I-Beam Frame
- Video: Review of Draw-Tite RV and Camper Hitch - Adjustable Frame Mount Hitch - 82201
- Shop: Trailer Hitch
- Q&A: Best Way to Install RV Trailer Hitch on I-Beam Frame with a 4 Inch Bumper Below on a 2014 Reflection
- Q&A: What is the Adjustable Width on the Ultra-Fab 2" Trailer Hitch Receiver UF35-946403
- Video: MORryde Tandem Axle Trailer Rubber Equalizers Manufacturer Demo
- Search Results: mor ryde
- Search Results: moryde
- Video: Curt RV Bumper Trailer Hitch Receiver Review
- Video: Draw-Tite RV and Camper Hitch - Frame Mount Hitch - 5350 Review
- Video: Mount-n-Lock HiLoHitch Installation - 2017 Keystone Hideout Travel Trailer
- Search Results: rear camper trailer hitch
- Search Results: curt 13703
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: Roof Rack
Mark A.
8/12/2020
will this fit a 305g momentum toy hauler. there is a two inch drop between the I-beam and rear steel 6 inch solid bumper. can i reverse the cross bars to drop the 2" receiver to clear the rear cross member/bumper. the inner I-ibeam width is 71". the frame is heavy duty as well as the rear cross member.