Wheel and Tire Recommendation for 20.5 x 8.0 x 10 on Wheel with 5 on 5-1/2 inch Bolt Pattern

Question

Question:

Looking to purchase 2 Tires and Rim Combinations for my 1996 Tracker Pontoon Trailer . I prefer Hot Dipped Galvanized Rims and the Tire Size in 20.5 x 8.0 x 10 inch or Radial Equivalent Lug Spacing is: 5 on 5.5

asked by: Charles G

0

Expert Reply:

In the tire size and bolt pattern size you need we only have white wheels. The bolt pattern you have is not the most popular so that's why the options are a bit limited.

So you would need the part # AM3H454 which has the correct tire size and wheel bolt pattern.

expert reply by: Jameson C

0

Answer 1

We have the part #AM3H454 which matches the criteria you mentioned. It is a 20.5 x 8 - 10 tire Load Range E mounted on a wheel with a 5 on 5 inch bolt pattern.

view full answer...

Answer 2

The 205/50-10 is the modern replacement size for the 20.5x8-10 tire. The #AM3H454 wheel/tire combo you specified has a 1650 lb per tire capacity. My research indicates that the 20.5x8-10 Load Range F tire had a 1765 lb per tire capacity which is…

view full answer...

Answer 3

The modern day equivalent of a 20.5 x 8-10 tire is going to be a 205/65-10. The dimensions are as close as you can get to the old size. We have several tires and tire and wheel combos in this size with various bolt patterns (if a wheel is needed).…

view full answer...

Answer 4

The Kenda 205/65-10 Bias Trailer Tire with 10" Galvanized Wheel part #AM3H440 has a maximum speed rating of 65 mph. In order to obtain a higher speed rating you will need to upgrade to a substantially larger tire size like the Karrier…

view full answer...

Answer 5

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Answer 6

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 7

For any trailer (including dolly) tires such as your Loadstar #AM1HP52, you always want to inflate them to the maximum cold psi, which on this tire is 50. Doing this will give you the best performance, allowing the tire to wear slower and more evenly…

view full answer...

Answer 8

The correct air pressure for your Kenda Loadstar 205/65-10 tires will be dependent on the load rating of your tires, and you will want to make sure they are aired up to the maximum PSI of the tire which will be stamped on the sidewall. Also go ahead…

view full answer...

Answer 9

The speed rating of the Kenda Loadstar 205/65-10 Bias Trailer Tire with 10" Solid Center Wheel #AM3H454 you were looking at is 87 mph. This tire and wheel combo has a 5 on 5-1/2 lug pattern and a maximum load capacity of 1,650 lbs at 90 psi.

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Wheel and Tire Recommendation for 20.5 x 8.0 x 10 on Wheel with 5 on 5-1/2 inch Bolt Pattern

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching