Removing Lenses of Optronics Fender Light and Replacing Bulbs with LEDs

Question

Question:

Your Item# BA44FNL and FNR. I have those on my trailer. I cannot figure out how to remove lens covers to access bulbs. I dont want to break / crack them. Are you able to send me picture or describe how to do that? Your online review of product doesnt show. Also, are there LED replacements or substitutes for both the red and amber lens. Ideas / suggestions??

asked by: Ron R

0

Expert Reply:

The lens of # BA44FNR and # BA44FNL should pop off if you take a small flat head screw driver and pry it off. Unfortunately, we don't have any videos or instructions that show the removal.

For replacement LED bulbs you can use # P340194A-360.

expert reply by: Charles S

0

Answer 1

It sounds like there is a short circuit that is overloading the running light circuit in the tow package wiring on your tow vehicle. The most likely culprit is a dirty or corroded trailer connector on the vehicle or trailer if not both. The first…

view full answer...

Answer 2

To determine the correct air pressure for the tires on your Jayco trailer take a look at the sidewall. The tires should have the maximum psi listed. Trailer tires should always be inflated to the maximum psi indicated on the tire. This is because…

view full answer...

Answer 3

We do offer all sorts of trailer lighting, including fender-mount types such as #BA44FNL and #BA44FNR which are combination red/amber lights. We also have #MCL61ARB. These and all other red/amber lights are shown on the linked page. If you cannot…

view full answer...

Answer 4

We do indeed have that particular fender clearance/marker light, we refer to it by our part number, which is #OPT36FR.

view full answer...

Answer 5

I pulled the 2 trailer lights you asked about so that I could take some measurements you wanted. I have attached a couple of photos with the dimensions noted on the photo. Part #BA65ARRB measures 5-7/16 inches long and 3-3/16 inches wide, and is used…

view full answer...

Answer 6

In regards to the Linxup GPS Tracking Device part #300-AT3, once you install the GPS device, you'll be ready to choose and set up the Linxup service plan that works for you. When you purchase a service plan, you can download the Linxup mobile app…

view full answer...

Answer 7

I spoke to Linxup and they informed me that if the battery is completely drained on the Linxup GPS Tracking Device #300-AT3, that it would take between 4-8 hours to fully charge the battery. Once charged the battery will last up to 3 months as while…

view full answer...

Answer 8

For your application the Lilnxup GPS Tracking Device, part #300-AT3, would be the way to go. It installs anywhere on your trailer.

view full answer...

Answer 9

We have the perfect solution. You can use a Linxup GPS Tracking Device, part #300-AT3. Using the associated app you can track the trailer, see how much it has moved, set up a "fence" around the trailer so if it leaves that area you will be…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

You have it right so far, the 4-way connector is just as you have stated. Remember that Yellow has a L in it so that is the left side brake/turn signal and green has a R in it so that is the right side brake/turn signal. The colors for wiring a 7-way…

view full answer...

Answer 12

For your AL-KO 7210 braking assembly, you can use the Hydraulic Brake Kit #AKFBBRK-7 as a replacement. These braking assemblies measure 12" x 2", bolts onto a 5 bolt mounting flange, will work with wheel sizes from 14-1/2" to…

view full answer...

Removing Lenses of Optronics Fender Light and Replacing Bulbs with LEDs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching