Recommended Trailer Hitch Receiver And Towing Accessories For 2013 Ford Fusion For Towing Jet Ski
Question:
I have an 1992 Polaris Jet ski that I would like to pull using my 2013 ford fusion. What hitch and accessories would you recommend that I use.
asked by: Randy B
Helpful Expert Reply:
For your 2013 Ford Fusion, I recommend the Curt Class II trailer hitch receiver # C12091. This hitch is compatible with the S and SE models as well as the Titanium model. For a ball mount, I recommend the Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs # C45016 along with a hitch ball to match your trailer coupler. For a 2 inch ball, I recommend # A-82 and for a 1-7/8 inch ball # A-80. You will also need a pin and clip like # F-4, or a locking pin like the # e98879.
For your vehicle trailer wiring harness, I recommend the Tekonsha T-One Vehicle Wiring Harness # 118574. This harness will plug into your factory wiring behind the driver and passenger side tail lights. It will be powered directly by your vehicle battery so your vehicle's electrical system will be protected from overload. I've attached an article to assist with running that power wire.
This will provide you with a complete system for your 2013 Ford Fusion.
Products Referenced in This Question
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
etrailer Trailer Hitch Receiver Lock for 1-1/4" Hitches - Flush - 2-1/8" Span - Chrome
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Alike
- Chrome
- Fits 1-1/4 Inch Hitch
- Flush Pin
- 2-1/8 Inch Span
- etrailer
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 350 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Seal With Dimensions to Replace 171255UC
- Article: How Long Can You Boondock in an RV?
- Q&A: How Much Upward Bend Should Trailer Axle Have
- Q&A: Is Bow in 3,500 lb Trailer Axle Enough Camber for Loaded and Unloaded Trailers
- Q&A: Replacement Clearance Lights Needed for GLO-BRITE 122R and 122Y Lights
- Article: Trailer Wiring Diagrams
- Q&A: Recommended Generator Set for 2019 Forest River Salem 30KQBSS Travel Trailer
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Can Redline 2-Way Pop-Up Roof Vent # 9106-2756 be Used in Rain
- Q&A: Comparison between Kuat Transfer and Swagman Chinook Bike Racks
- Article: Gooseneck Trailer Hitch Information and Review
- Article: Stability Control for Heavy Duty Vehicles
- Article: Steel vs. Aluminum Ball Mounts
- Article: Ball Mount Basics: Weight Capacity, Class, and Size