Tow Mirror Solution for 2013 GMC Sierra with Chrome Mirrors

Question

Question:

I have factory chrome mirrors, not after market caps, will Item # CM10900 fit my 2013 GMC Sierra?

asked by: Grant S

0

Expert Reply:

The part # CM10900 does not fit the chrome mirrors of a 2013 GMC Sierra.

You would want to go with a door mounted tow mirror to bypass this with like the CIPA part # 11650. I attached an install video for this mirror on a similar 2011 GMC Sierra as yours as well.

expert reply by: Jameson C

0

Answer 1

Yes, If you replace the chrome caps on your 2012 Chevy Silverado 1500 with the black plastic caps you mentioned then both the CIPA #CM10900 and K-Source #KS80900 will work. Between these two I personally like the K-source as I seem to see better…

view full answer...

Answer 2

The CIPA Custom Towing Mirrors - Slip On - Driver Side and Passenger Side Item #CM10900 are not a confirmed fit for your 2020 Tahoe. The K-Source Snap & Zap Custom Towing Mirrors - Snap On - Driver and Passenger Side #KS80920 are a confirmed…

view full answer...

Answer 3

For your 2013 Chevrolet Silverado I suggest the CIPA Custom Towing Mirrors #CM10900. These are the most popular towing mirrors we carry for your truck and will fit whether you have manual or powered mirrors wtih and without the heating feature. See…

view full answer...

Answer 4

Yes, the CIPA Custom Towing Mirrors - Slip On - Driver Side and Passenger Side, part #CM10900, will fit your 2013 GMC Yukon Denali. I have included a video mirrors being installed on a 2010 GMC Yukon below.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...