Troubleshooting AirLIft Wireless Controller with Error Message
Question:
The remote will not respond to the compressor it come up as fail
asked by: David P
Expert Reply:
The Air Lift Wireless AIR Compressor System # AL74000 will show an error whenever there is any type of issue with the system.
Generally this is an issue with the remote communicating with the system, a blockage, or a leak. I would inspect the compressor system and all of the air lines to make sure there are no issues. You can check for leaks using soap and water. If you find a leak disconnect the hose and make sure the tubing is cut as square as possible. If you find a block you'll likely need to replace that piece of tubing.
If you don't find anything wrong with the system try to join the controller with the manifold again:
Set the manifold into join mode.
• Ground the join wire in the electrical harness.
• Locate the YELLOW join wire with heat shrink on the end in the harness.
• Remove the yellow wire from the cap leaving the cap atached to the
harness.
• Attach the exposed terminal to a good frame ground.
Cycle power to the manifold.
• Manifold will boot in join mode and will click the exhaust solenoid 5 times fast,
then 1 per second.
• The manifold will stay in join mode for 30 seconds allowing time to set the
controller into join mode.
Set the controller into join mode.
• Press UP and DN buttons together to enter Settings Mode.
• Press the M1 button when the display flashes “JOIn”.
• Use the up and down buttons to select which manifold to join with.
• JOIn r = Join with the manifold controlling the rear axle springs.
• JOIn F = Join with the manifold controlling the front axle springs.
• Press the M1 button to join the controller to the selected manifold.
• The display will show DONE when the joining process is complete.
• The M2 button will exit back to the settings mode.
• Press M2 button again to exit out of Settings Mode.
• Disconnect yellow wire from ground.
• Reinsert the yellow wire terminal into the molded cap
Product Page this Question was Asked From
Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth
- Air Suspension Compressor Kit
- Wireless Control
- Dual Path
- Digital Display
- 100 psi
- Air Lift
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Suspension Enhancement
- Search Results: 40975
- Shop: Air Lift WirelessONE Compressor System for Air Helper Springs - Remote - Bluetooth - EZ Mount
- Shop: Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Top Load
- Shop: Base Plate for Tow Bar
- Video: Review of B and W Replacement Latch Pin Handle Turnoverball Underbed Gooseneck Hitch - BW1900-2-2007
- Shop: Dexter Fortress Threaded Aluminum Oil Cap for 9K to 10K Axles
- Shop: Curt Replacement OEM USCAR Trailer Connector - Dual Connection - 7-Way RV Style and 4-Way Flat
- Search Results: 010 051 00
- Shop: Equalizer for 2-1/2" Wide Slipper Springs - LH or RH - 18-3/8" Long - 1" Center Hole
- Search Results: cta~cb4
- Shop: Brake Controller
- Shop: Hopkins Trailer Connector Adapter - 7-Pole Round Pin to 7-Pole RV
- Shop: Gooseneck Hitch
- Search Results: 25980
- Search Results: 89338
- Shop: Vehicle Tow Bar Wiring
- Search Results: tcslip~g70~8~l
- Shop: Replacement Cable and Pin for Hopkins LED Breakaway Switches
- Search Results: pk12~724
- Video: PackEm Cargo Control Rack for Enclosed Trailers Review
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2018 Ford Escape
- Video: Curt Custom Fit Vehicle Wiring - Trailer Hitch Wiring - C56320 Review
- Q&A: Troubleshooting the Comp Freeze Error Code on Air Lift Compressor Remote
- Q&A: Troubleshooting Remote On Air Lift No Longer Joining To Manifold
- Q&A: Troubleshooting Air Lift WirelessONE Remote Not Working
- Q&A: Replacement Seal Recommendation for Dexter 010-004-00
- Q&A: The Remote Says Fail, Is There A Reset On The Air Lift WirelessAIR Compressor System