How To Pair an Air Lift WirelessAIR Remote to Compressor
Question:
How to program a new wireless controller to the compressor???
asked by: Oscar R
Expert Reply:
In the settings mode of the controller you can join the manifolds with the controller.
To set the manifold into join mode locate the yellow join wire. It is the yellow wire with heat shrink on the end of it. Remove the cap leaving it attached to the harness. Attach the exposed terminal to a good frame ground. Now the manifold will boot into join mode and will click the exhaust solenoid 5 times fast then one per second. The manifold will stay in join mode for 30 seconds.
On the controller hold the up and down buttons together. Cycle through the different options at this point by pressing the up button. Once you see Join on the display press the M1 button.
Use the up and down button to select which axle you want to join with. Press M1 when you have selected the correct axle you want. The display will show done when complete.
Disconnect the yellow wire from the ground and reconnect into the molded cap.
Product Page this Question was Asked From
Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth
- Air Suspension Compressor Kit
- Wireless Control
- Dual Path
- Digital Display
- 100 psi
- Air Lift
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Replacement Remote Control for Air Lift WirelessONE Compressor System
- Shop: Replacement Remote for Air Lift WirelessONE Compressor System for Air Helper Springs
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Video: Review of Redarc Trailer Brake Controller - Tow Pro Liberty Proportional Controller - RED24FR
- Shop: B&W Tow & Stow 3-Ball Mount - 3" Hitch - 4-1/2" Drop, 4" Rise - 21K - Black
- Video: Review of Redarc Trailer Brake Controller Parts - Universal Wiring Harness - RED69FR
- Shop: Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Q&A: Pairing the Replacement Wireless Remote to the Air Lift WirelessAIR Compressor System
- Shop: Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth
- Q&A: The Remote Says Fail, Is There A Reset On The Air Lift WirelessAIR Compressor System
- Q&A: Air Lift Wireless Remote Control Replacement For Remote 73001 and Pairing Instructions
- Search Results: locking trailer pin
- Q&A: Troubleshooting Air Lift WirelessONE Remote Not Working
- Q&A: Does B&W Tow & Stow 3-Ball Mount # BWTS30048B Come with Hitch Pin
- Search Results: 57341
- Video: Air Lift Loadlifter on a 5000 Air Helper Spring Installation - 2019 Chevrolet Silverado 2500
- Q&A: How to Pair New Remote With Air Lift WirelessAIR Compressor System
- Video: Air Lift Vehicle Suspension AL72704 Review
- Video: Air Lift WirelessAIR Compressor System Review
- Q&A: Troubleshooting AirLIft Wireless Controller with Error Message
- Video: Review of TorkLift Hitch Adapters - Hitch Extender - TLE1648
- Search Results: air lift rear axle suspension enhancement
- Video: Air Lift WirelessONE Compressor System Remote Control Replacement Review
- Search Results: 25980
- Search Results: airlift controller
- Search Results: led strip
- Shop: Camper Tie-Downs
Greg
4/28/2020
Hi the batteries went dead in my remote thought So i replaced the batteries. The screen is still blank none of the buttons respond. Thank you