The Remote Says Fail, Is There A Reset On The Air Lift WirelessAIR Compressor System
Question:
The remote display says fail when trying to use my air lift. I changed the remote batteries. Is there a reset on the compressor?
asked by: Dave
Expert Reply:
Generally this is an issue with the remote # AL73002 communicating with the system # AL74000, a blockage, or a leak. I would inspect the compressor system and all of the air lines to make sure there are no issues. You can check for leaks using soap and water. If you find a leak disconnect the hose and make sure the tubing is cut as square as possible. If you find a block you'll likely need to replace that piece of tubing.
If you don't find anything wrong with the system try to join the controller with the manifold again:
Set the manifold into join mode.
• Ground the join wire in the electrical harness.
• Locate the YELLOW join wire with heat shrink on the end in the harness.
• Remove the yellow wire from the cap leaving the cap atached to the
harness.
• Attach the exposed terminal to a good frame ground.
Cycle power to the manifold.
• Manifold will boot in join mode and will click the exhaust solenoid 5 times fast,
then 1 per second.
• The manifold will stay in join mode for 30 seconds allowing time to set the
controller into join mode.
Set the controller into join mode.
• Press UP and DN buttons together to enter Settings Mode.
• Press the M1 button when the display flashes “JOIn”.
• Use the up and down buttons to select which manifold to join with.
• JOIn r = Join with the manifold controlling the rear axle springs.
• JOIn F = Join with the manifold controlling the front axle springs.
• Press the M1 button to join the controller to the selected manifold.
• The display will show DONE when the joining process is complete.
• The M2 button will exit back to the settings mode.
• Press M2 button again to exit out of Settings Mode.
• Disconnect yellow wire from ground.
• Reinsert the yellow wire terminal into the molded cap
Products Referenced in This Question
Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth
- Air Suspension Compressor Kit
- Wireless Control
- Dual Path
- Digital Display
- 100 psi
- Air Lift
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Suspension Enhancement
- Shop: Trailer Hitch
- Shop: Gooseneck Hitch
- Shop: Trailer Wiring
- Shop: Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth - EZ Mount
- Shop: Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs - Rear Axle
- Q&A: Replacement Module for Air Lift Compressor
- Shop: Base Plate for Tow Bar
- Shop: Vehicle Tow Bar Brake System
- Shop: B&W Ball and Safety Chain Kit for Ford, GM, Chevy, and Nissan Titan XD Underbed Gooseneck Hitch
- Shop: Reese Pro Round Bar Weight Distribution w Sway Control - Round Bar - 8,000 lbs GTW, 800 lbs TW
- Shop: Roadmaster Universal Stop Light Switch Kit
- Search Results: 751000
- Shop: Air Lift WirelessAIR Suspension System for Air Helper Springs Kit - Remote - Bluetooth - EZ Mount
- Shop: etrailer Trailer Wheel Lock
- Video: Air Lift WirelessAIR Compressor System for Air Helper Springs Installation - 2022 Ford F-350 Super D
- Search Results: 61052
- Q&A: Troubleshooting a Remote for an AirLift Performance 3P That Is No Longer Working
- Search Results: 9332
- Search Results: 98160
- Search Results: air lift compressor
- Search Results: air lift compressor
- Search Results: air suspension compressor kit
- Video: GCH Automotive Truck Bed Accessories - Truck Bed Cargo Camera - 3460009 Review
- Video: GCH Automotive Truck Bed Accessories - Truck Bed Cargo Camera - 3460008 Review
- Video: Gooseneck Trailer Hitch Installation - 2014 Ram 3500
- Q&A: Reset for Air Lift WirelessAIR Compressor System
- Q&A: Does a Spindle with Scarring and Complete Bearing Failure Need to be Replaced
- Q&A: Air Lift Wireless Remote Control Replacement For Remote 73001 and Pairing Instructions