2-1/2 Inch Shank For Weight Distribution System With 6 inches of Drop

Question

Question:

I need to replace my 2-1/2 weight distribution hitch shank with one that has a 6in drop and need assistance getting the correct one.

asked by: John D

0

Expert Reply:

The Equal-i-zer shank # EQ90-02-4900 is designed to fit 2-1/2 inch hitches and has a maximum 6 inch drop.

expert reply by: Jameson C

0

Answer 1

Yes. The 2-1/2 inch shanks like #EQ90-02-4700 or #EQ90-02-4900 will allow you to use the same Fastway e2 system. The shanks are not brand specific and are often interchangeable to meet your specific needs. I recommend the Equal-I-zer because they are…

view full answer...

Answer 2

The BulletProof Hitches 2-Ball Mount for 2-1/2" Hitch #MD256 has an 8-1/4" drop and 8-1/2" rise. BulletProof Hitches does not follow the standard measurement which is where the confusion is coming from. Rise is the distance from the…

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 5

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 8

The Correct Track Trailer Alignment and Lift Kit - Tandem Axle #RR23QX does come with all of the components needed to lift a tandem axle trailer. The center hangers of a tandem axle setup use different components than the front and rear hangers since…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

2-1/2 Inch Shank For Weight Distribution System With 6 inches of Drop

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching