Replacement Head Tilt Spacer Washers for Equal-I-zer EQ37100 Weight Distribution Hitch

Question

Question:

My RV dealer installed my # EQ37100ET hitch. He only installed 3 of the spacer washers and threw away the other 3. Can you tell me what size washers these are so I can get replacements? Also should I buy SS or zinc plated? Thank you.

asked by: Jim S

0

Expert Reply:

Equal-I-zer uses a 3/4 inch brass washer. We sell the washers along with the spacer rivet as part # EQ95-01-9450. I'd recommend sticking with brass washers if at all possible.

expert reply by: Mike L

0

Answer 1

The hitch ball angle adjustment on weight distribution systems is designed to provide more or less distribution of the tongue weight on your trailer hitch to the trailer and vehicle axles. If you adjust the ball angle farther away from the towing…

view full answer...

Answer 2

The typical springs for the AL-KO 4,400 axles are one of two lengths. If you have the 25-1/4 inch length, then you will want the 4-Leaf Double-Eye Spring for 5,000-lb Trailer Axles #e28SR, but if you have the 26 inch springs, you will want the 6-Leaf…

view full answer...

Answer 3

The best matching leaf springs we offer for a 4,400 lb axle is going to be the #e27SR which is for 4,500 lb axles and has the very common spring length of 26 inches.

view full answer...

Answer 4

The 5/8" diameter x 4-1/2" long bolts and nuts in the 4k Replacement Bolts for Equal-i-zer Weight Distribution Head #EQ90-02-9400 are both 15/16" head sizes. The 6k-14k Replacement Bolts for Equal-i-zer Weight Distribution Head…

view full answer...

Answer 5

Weight distribution spring bar tension can be increased by tilting the head toward the trailer so that the ends of the spring bars are closer to the ground. Once connected to the lift brackets this increased angle translates into more tension, which…

view full answer...

Answer 6

To measure for the correct leaf spring length, you should jack up the trailer so that the axle hangs free, then measure straight across from the center of one eye to the center of the other eye. Because springs tend to flatten out as they wear, this…

view full answer...

Answer 7

You can use the 25-1/4" 4-Leaf Double-Eye Spring for 5,000-lb Trailer Axles #e44SR to replace your current leaf springs that measure 26" from eye to eye. What happens is that leaf springs will stretch out and flatten over time. So if your…

view full answer...

Answer 8

The Solera Awnbrella Support Kit for 8' Projection RV Awning - 3 Pack #LC362237 is designed to work with most 8' projection awnings that are between 14' and 18' wide. Though I could not find anything about these being used with a…

view full answer...

Answer 9

Congrats on the new trailer! However you need to know the loaded tongue weight of your trailer, as the dry weight is not a useful figure. With your trailer fully loaded like you'll be towing it use either the scale method in the below help…

view full answer...

Answer 10

Most of the time when a tow setup is porpoising with a weight distribution system all you have to do is add a bit more spring bar tension to minimize the porpoising. With an Equalizer system you would need to angle the spring bars down further to add…

view full answer...

Answer 11

If you have a newer Reese weight distribution system like the Reese Strait-Line Weight Distribution, #RP66074, with the trunnion spring bars and the integrated cam ends then you will be able to install the heavier spring bars. The heavier spring bars…

view full answer...

Answer 12

The round or trunnion bars refers to the end of the spring bars. Round bars are typically designed for lighter applications, are a bit harder to install and are usually priced lower than trunnion bars. Trunnion bars are typically designed to be used…

view full answer...

Replacement Head Tilt Spacer Washers for Equal-I-zer EQ37100 Weight Distribution Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching