Long Shank Recommendation for an Equalizer E2 Weight Distribution System
Question:
I have an E2 equklizing hitch and it has a 12inch shank, which has an 8inch measurement from the hitch hole to the adjustment hole. Using this shank I am unable to lower the tailgate on my pickup GMC 2500 HD if it helps. I would like to get a longer shank so that the trailer can sit back further. The tongue weight on the trailer is 620lbs. Any suggestions?
asked by: Bill K
Expert Reply:
Sounds like you are looking for the Curt Weight Distribution Shank part # C17122. This shank is 14 inches from the hitch pin hole to the vertical adjustment holes that the head of the system will install to. This will also work with your E2 Fastway weight distribution system as well.
I attached a dimension picture for this shank as well.
Products Referenced in This Question
Curt Weight Distribution Shank - 14" Long - 7" or 7-1/2" Drop - 1,500 lbs TW
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- Fits 2 Inch Hitch
- Round - 7 Inch Drop
- Trunnion - 5 Inch Drop
- Round - 10 Inch Rise
- Trunnion - 11 Inch Rise
- CURT
more information >
Product Page this Question was Asked From
Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- 1400 lbs TW
- Fits 2-1/2 Inch Hitch
- Equal-i-zer
- Square - 3 Inch Drop
- Square - 7 Inch Rise
- Equal-i-zer
more information >
Continue Researching
- Shop: Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop
- Search Results: equalizer shank
- Q&A: Can a 2-1/2 WD Shank be Used with a System that Uses a 2 Shank
- Shop: Torque Wrench with Storage Case - 3/8" Drive - 100 ft/lbs of Torque
- Search Results: weight distribution
- Search Results: weight distribution sway control
- Video: Review of Equal-i-zer Weight Distribution Parts - Shank for 2-1/2 Inch Hitch - EQ90-02-4700
- Shop: Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 10" Rise/6" Drop
- Article: How to Measure for Trailer Hitch Drop
- Search Results: eq90~02~4700
- Q&A: Can Other Brands of Weight Distribution Heads be Used with Equalizer Shank # EQ90-02-4700
- Shop: etrailer Magnetic Hitch Receiver Reducer Sleeve - 2-1/2" to 2" Hitch - 5" Long
- Shop: B&W Hitch Receiver Reducer Sleeve - 2-1/2" to 2"
- Q&A: Replacement Fuse for the Stromberg Carlson Electric A-Frame Tongue Jack # JET-2500
- Shop: Trailer Coupler 2" Ball 3" Channel Tongue (3,500 lbs.) by Dutton-Lainson
- Shop: Curt Weight Distribution Shank for 2-1/2" Hitches - 6-3/4" Rise - 3-1/4" Drop
- Q&A: Weight Distribution Shank that Allows Truck Tailgate to Fold Down
- Search Results: 2.5" receiver hitch
- Q&A: Can I Change My Trailer Coupler from a 1-7/8 Inch Coupler to a 2 Inch Coupler
- Q&A: Needing 7-Hole Weight Distribution Shank for 2-1/2 Inch Reciver
- Q&A: Is There a 2-1/2" Shank for the Blue Ox TrackPro Weight Distribution System
- Article: How to Install a Weight Distribution Hitch (With Pictures & Video)
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Hitch
- Article: 5 Things to Know About Weight Distribution Hitches
- Video: Choosing the Right Brake Controller
- Shop: Trailer Wiring
- Search Results: dust cap
- Shop: Fifth Wheel Hitch