How to Pick Out a Grease Seal for a 5,200 lb Axle that Has Hubs with 6 on 5-1/2 inch Bolt Pattern

Question

Question:

I have a 2002 Pace 28ft enclosed race car trailer with 6 lug 5200 axles. Which seals do I need ?

asked by: Jeff C

0

Expert Reply:

Based on the information you provided I am nearly positive you would need the part # RG06-070 for replacement seals as these have an ID of 2.250 and an OD of 3.376. Based on the lug pattern and weight capacity of your axles these would be the correct seals for most trailer axles.

You can pull off your trailer hub and measure the seal to be certain though.

expert reply by: Jameson C

0

click to enlarge

Answer 1

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 2

For a 12,000 lb. electric car trailer winch like the Bulldog Winch Trailer Winch part #BDW10040, I recommend a standard 12 volt lead acid battery rated up to at least 650 cold cranking amps (CCA). As long as the battery is rated up to 650 CCA then…

view full answer...

Answer 3

Trailair Flex Air 5th Wheel Pin Boxes, such as the Lippert #LC328492, are designed to replace the existing pin box on your trailer. The long and short jaw models that you referenced in your question simply refer to the type of pin box that the unit…

view full answer...

Answer 4

The correct grease seals for a Grand Design Reflection 367 BHS with Dexter 7K Axle are the Grease Seals part #RG06-070.

view full answer...

Answer 5

One common grease seal size for a 6,000 lb axle has an inner diameter of 2.25" and outer diameter of 3.376" just like the #RG06-070. More than likely this matches what you have now, but you can't be 100% sure without either measuring or…

view full answer...

Answer 6

Correct, although the TruRyde Seal part #RG06-070 has the same dimensions as the Dexter Seal part K71-386-00, the TruRyde is for grease and the Dexter is for oil. The Dexter Seal part K71-386-00 cross-references to our Unitized Oil Seal for Trailer…

view full answer...

Answer 7

For a 5,200 lb Lippert axle the correct hub seal is the part #GS-2250DL.

view full answer...

Answer 8

Yes, the RG06-090 replaces the National 470972. On the product page we have a link to the cross-reference for the National part number.

view full answer...

Answer 9

The grease seals in Kit #BK3-100 are not the same as 21333TB. The correct replacement seal for that would be #RG06-090, which have a 2.125" inner diameter and 3.376" outer diameter.

view full answer...

Answer 10

You said 3.376 x 2.125 od, but I believe you were referring to 3.376 inch outer diameter x 2.125 inch inner diameter. If so, we can indeed help and have the correct part for you with the following: - 10-10 Grease or Oil Double-Lip Seals #RG06-090 The…

view full answer...

Answer 11

The first thing you will need to check is if there is enough space around the existing tires to use the larger size. Based on the old size you have, 235/75-15 (which isn't a common trailer tire size) the tires are approximately 28.8 inches tall…

view full answer...

Answer 12

You will need the part #RG06-070. I looked up the K71-386-00 seal that you mentioned and it has an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. This seal is normally seen on 5.2k Dexter axles all the way up to 8k axles.

view full answer...

How to Pick Out a Grease Seal for a 5,200 lb Axle that Has Hubs with 6 on 5-1/2 inch Bolt Pattern

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching