Brake Controller Wiring Adapter for 2012 Toyota Tundra

Question

Question:

tell me the proper adapter for pilot brake control unit and where does wires come out in rear of truck

asked by: Doreen P

0

Expert Reply:

The proper brake controller wiring adapter is # 3040-P, which would plug into the connector located to the left and above the emergency brake pedal, as shown in the photo I provided. If your truck doesn't have the 7-way connector, you can install one using part # HM11143395 which plugs into the connector located behind the rear bumper of the truck.

If you have the older version Pilot brake controller that simply has the bare wires exiting the rear, you'd cut the black plug off your 3040-P and wire it directly to the brake controller, color for color.

expert reply by: Mike L

0

click to enlarge

Answer 1

I took a look at the owner's manual for a 2012 Toyota Tundra and its ratings for towing a fifth wheel trailer are based on the GCWR (Gross Combination Weight Rating), which is the weight of your fully loaded '12 Tundra PLUS the weight of a…

view full answer...

Answer 2

If your 2011 Tundra has the factory tow package, which includes the factory installed 7-way trailer connector on the rear bumper, it will be equipped with the tow package plug under the dash, as shown in the photo I've edited for you. Some models…

view full answer...

Answer 3

The one really big downside to gooseneck towing is that there isn't a great solution for short bed truck clearance unlike fifth wheel towing. With fifth wheel hitches you can use a slider hitch and have the clearance issue handled. With gooseneck…

view full answer...

Answer 4

For a trailer weighing 1200kg (2640 pounds) you would most likely only need boost setting 1 if at all when using the P3, #90195. But before setting the boost you will need to set the gain properly on the P3. To do this, follow these steps: First take…

view full answer...

Answer 5

I am assuming you mean that the P3 display remains lit when the trailer is connected after the vehicle ignition is switched off. The display of the P3 will remain active for up to 15 minutes after the ignition is turned off, at which point the screen…

view full answer...

Answer 6

We do have a wiring adapter with a pigtail that will allow you to splice it into a brake controller and that will fit your 2019 Toyota Tacoma. The part you need is the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - Toyota…

view full answer...

Answer 7

As long as you stay under the 10,300 pound mark you should be fine. Currently your trailer and gear estimate would weigh 9,100 pounds. Take a look at the rig when the trailer and truck are fully loaded as though you were ready to hit the road. If the…

view full answer...

Answer 8

The individual links on a weight distribution system like the #RP66541 do not represent different tongue weight values. It really just comes down to following the setup procedure that is outlined in the install instructions which are attached which…

view full answer...

Answer 9

In order to install a 7-way trailer wiring harness in the bed of your 2010 Ford F-250 while also still allowing for the factory 7-way at the bumper, you are going to want to use the Curt 5th Wheel/Gooseneck Custom Wiring Harness part #C56070. I have…

view full answer...

Answer 10

If your 2018 Toyota Tundra has the 6-1/2 foot bed, I recommend the Curt Custom Fifth Wheel Installation Kit #C16468-204. This installation kit includes custom-fit brackets that are confirmed to fit your truck and will use existing holes in the…

view full answer...

Answer 11

I checked with Curt and the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7 Long Item #C56070 would require 7 inches of clearance on the inner side of the fender/bed wall to install.

view full answer...

Answer 12

Yes, you can use the Curt 5th wheel and gooseneck in-bed wiring harness #C56070 in a truck with a drop-in bed liner. You will need to cut a hole through the bed liner as well as the bed for installation. If you want you can make the bed liner hole…

view full answer...

Brake Controller Wiring Adapter for 2012 Toyota Tundra

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching