Pigtail Brake Controller Wiring Adapter for 2019 Toyota Tacoma to Splice to Brake Controller

Question

Question:

I have a Draw-Tite Activator that was removed from one vehicle and I want to install into another. The controller was installed in the first vehicle by splicing the 4 wires from the controller directly to the corresponding wires under the dash. Does there exist an adapter of sorts that will allow me to spice a replacement connector to the cut wires of the controller so that I can then plug it into the second vehicles trailer brake harness? Instead of directly splicing it to the harness/wiring as was done in the first vehicle. 2019 Toyota Tacoma Thank you.

asked by: Keith J

0

Expert Reply:

We do have a wiring adapter with a pigtail that will allow you to splice it into a brake controller and that will fit your 2019 Toyota Tacoma.

The part you need is the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Pigtail - Toyota # 3031-S.

You will simply splice the wires color for color to the brake controller with the included butt connectors.

expert reply by: Kyle S

0

Answer 1

While we don't carry the Kushner brand of brake controllers we can help you get the correct harness to install it in your 2022 Toyota Tacoma with the part #3031-S. With this connector you'd be able to connect the wires by color to your…

view full answer...

Answer 2

What you will need to install your Hopkins brake controller in your 2015 Toyota Tundra is the install harness part #3031-S. This harness has a connector that will plug into the port under the dash of your truck and then has 4 blunt cut wires that…

view full answer...

Answer 3

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

Most critical to trailer tire performance and durability are 1) proper inflation 2) observance of the tire's rated load capacity and 3) observance of the tire's speed rating. If either of these factors is off the mark then the tire will tend…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option. A…

view full answer...

Answer 10

I'm pretty sure you are correct that the Coil SumoSprings Custom Helper Springs #CSS-1145R will fit your 2018 Toyota Highlander, however, we haven't had the chance to test this out and SuperSprings doesn't have this listed in their…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Pigtail Brake Controller Wiring Adapter for 2019 Toyota Tacoma to Splice to Brake Controller

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching